AT90USB82-16MUR Atmel, AT90USB82-16MUR Datasheet - Page 187
AT90USB82-16MUR
Manufacturer Part Number
AT90USB82-16MUR
Description
MCU AVR USB 8K FLASH 32-QFN
Manufacturer
Atmel
Series
AVR® 90USBr
Datasheet
1.AT90USB82-16MU.pdf
(307 pages)
Specifications of AT90USB82-16MUR
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
EBI/EMI, PS/2, SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
32-QFN
Data Bus Width
8 bit
Data Ram Size
512 B
Interface Type
SPI, USART, debugWIRE
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
22
Number Of Timers
2
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Lead Free Status / Rohs Status
Details
- Current page: 187 of 307
- Download datasheet (4Mb)
19.3.3
19.4
19.4.1
19.4.2
7707F–AVR–11/10
General Operating Modes
Design guidelines
Introduction
Power-on and reset
The USB controller is disabled and reset after a hardware reset generated by:
But another available and optionnal reset source is :
In this case, the USB controller is reset, but not disabled (so that the device remains attached).
The next diagram explains the USB controller main states on power-on:
Figure 19-7. USB controller states after reset
When the USB controller is in reset state:
• Serial resistors on USB Data lines must have 22 Ohms value (
• Traces from the input USB receptable (or from the cable connection in the case of a tethered
• Voltage transcient / ESD suppressors may also be used to prevent USB pads to be damaged
• U
• A 10µF capacitor is highly recommended on VBUS line
• USBE is not set
device) to the USB microcontroller pads should be as short as possibles, and follow
differential traces routing rules (same length, as near as possible, avoid vias accumulation).
by external disturbances.
cap
– Power on reset
– External reset
– Watchdog reset
– Brown out reset
– debugWIRE reset
– USB End Of Reset
capacitor should be 1µF (
Clock stopped
Dev ice
FRZCLK=1
+/-
Macro off
USBE=1
10%) for correct operation.
HW RESET from EOR
USBE=0
Reset
USBE=0
(excepted from EOR)
HW RESET
USBE=0
<any other
state>
AT90USB82/162
+/-
5%).
187
Related parts for AT90USB82-16MUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 8K FLASH 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: