ATMEGA88P-20MUR Atmel, ATMEGA88P-20MUR Datasheet - Page 71

• Manufacturer Part Number: ATMEGA88P-20MUR
• Description: MCU AVR 8KB FLASH 20MHZ 32QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA88P-20MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.2.4
12.2.5
8025L–AVR–7/10
PCICR – Pin Change Interrupt Control Register
PCIFR – Pin Change Interrupt Flag Register
• Bit 7:3 – Reserved
These bits are unused bits in the ATmega48P/88P/168P, and will always read as zero.
• Bit 2 – PCIE2: Pin Change Interrupt Enable 2
When the PCIE2 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 2 is enabled. Any change on any enabled PCINT[23:16] pin will cause an inter-
rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI2
Interrupt Vector. PCINT[23:16] pins are enabled individually by the PCMSK2 Register.
• Bit 1 – PCIE1: Pin Change Interrupt Enable 1
When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 1 is enabled. Any change on any enabled PCINT[14:8] pin will cause an inter-
rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI1
Interrupt Vector. PCINT[14:8] pins are enabled individually by the PCMSK1 Register.
• Bit 0 – PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 0 is enabled. Any change on any enabled PCINT[7:0] pin will cause an inter-
rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0
Interrupt Vector. PCINT[7:0] pins are enabled individually by the PCMSK0 Register.
• Bit 7:3 – Reserved
These bits are unused bits in the ATmega48P/88P/168P, and will always read as zero.
• Bit 2 – PCIF2: Pin Change Interrupt Flag 2
When a logic change on any PCINT[23:16] pin triggers an interrupt request, PCIF2 becomes set
(one). If the I-bit in SREG and the PCIE2 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 1 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT[14:8] pin triggers an interrupt request, PCIF1 becomes set
(one). If the I-bit in SREG and the PCIE1 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
Bit
(0x68)
Read/Write
Initial Value
Bit
0x1B (0x3B)
Read/Write
Initial Value
7
–
R
0
7
–
R
0
R
R
6
–
0
6
–
0
R
R
5
–
0
5
–
0
R
R
4
–
0
4
–
0
ATmega48P/88P/168P
3
–
R
0
3
–
R
0
PCIE2
PCIF2
R/W
R/W
2
0
2
0
PCIE1
PCIF1
R/W
R/W
1
0
1
0
PCIE0
PCIF0
R/W
R/W
0
0
0
0
PCICR
PCIFR
71