PIC16LC433T-I/SO Microchip Technology, PIC16LC433T-I/SO Datasheet - Page 11

• Manufacturer Part Number: PIC16LC433T-I/SO
• Description: IC MCU CMOS 8BIT 10MHZ 2K 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16LC433T-I/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: LIN (Local Interconnect Network)
• Peripherals: POR, WDT
• Number Of I /o: 6
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 18-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

TABLE 3-1:
GP0/AN0
GP1/AN1/V
GP2/T0CKI/AN2/INT
GP3/MCLR/V
GP4/OSC2/AN3/CLKOUT
GP5/OSC1/CLKIN
LIN bus
V
BACT
V
V
AV
AV
Legend: I = Input, O = Output, I/O = Input/Output, P = Power, — = not used, TTL = TTL input,
BAT
DD
SS
2001 Microchip Technology Inc.
DD
SS
ST = Schmitt Trigger input, OD = Open Drain
Name
REF
PP
PIC16C433 PINOUT DESCRIPTION
DIP Pin #
2,3,14,
13
12
18
17
16
15
11
8
6
1
4
5
7
I/O/P
Type
I/O
I/O
I/O
I/O
I/O
I/O
O
P
P
P
P
P
I
Advance Information
TTL/ST Bi-directional I/O port/serial programming data/analog input 0.
TTL/ST Bi-directional I/O port/serial programming clock/analog input 1/
TTL/ST Input port/master clear (RESET) input/programming voltage
TTL/ST Bi-directional IO port/oscillator crystal input/external clock
HV/OD High voltage bi-directional bus interface.
Buffer
Type
TTL
ST
—
—
—
—
—
—
Can be software programmed for internal weak pull-up and
interrupt-on-pin change. This buffer is a Schmitt Trigger input
when used in Serial Programming mode.
voltage reference. Can be software programmed for internal
weak pull-up and interrupt-on-pin change. This buffer is a
Schmitt Trigger input when used in Serial Programming mode.
T0CKI or external interrupt.
input. When configured as MCLR, this pin is an active low
RESET to the device. Voltage on MCLR/V
V
grammed for internal weak pull-up and interrupt-on-pin
change. Weak pull-up always on if configured as MCLR . This
buffer is Schmitt Trigger when in MCLR mode.
Connections to crystal or resonator in crystal oscillator mode
(HS, XT and LP modes only, GPIO in other modes). In EXTRC
and INTRC modes, the pin output can be configured to
CLKOUT, which has 1/4 the frequency of OSC1 and denotes
the instruction cycle rate.
source input (GPIO in INTRC mode only, OSC1 in all other
oscillator modes). Schmitt trigger input for EXTRC oscillator
mode.
Battery input voltage.
Bus activity output pin.
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Analog positive supply.
Analog ground.
Bi-directional I/O port/analog input 2. Can be configured as
Bi-directional I/O port/oscillator crystal output/analog input 3.
DD
during normal device operation. Can be software pro-
Description
PIC16C433
PP
DS41139A-page 9
must not exceed