AT89LP6440-20PU Atmel, AT89LP6440-20PU Datasheet - Page 156
AT89LP6440-20PU
Manufacturer Part Number
AT89LP6440-20PU
Description
MCU 8051 64K FLASH ISP 40PDIP
Manufacturer
Atmel
Series
89LPr
Datasheet
1.AT89LP6440-20MU.pdf
(194 pages)
Specifications of AT89LP6440-20PU
Core Processor
8051
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
38
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Eeprom Size
8K x 8
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.4 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 156 of 194
- Download datasheet (6Mb)
24.2
24.3
156
Software Breakpoints
Limitations of On-Chip Debug
AT89LP6440 - Preliminary
Figure 24-1. AT89LP6440 On-Chip Debug Connections
The AT89LP6440 microcontroller includes a BREAK instruction for implementing program mem-
ory breakpoints in software. A software breakpoint can be inserted manually by placing the
BREAK instruction in the program code. Some emulator systems may allow for automatic inser-
tion/deletion of software breakpoints. The Flash memory must be re-programmed each time a
software breakpoint is changed. Frequent insertions/deletions of software breakpoints will
reduce the endurance of the nonvolatile memory. Devices used for debugging purposes should
not be shipped to end customers. The BREAK instruction is treated as a two-cycle NOP when
OCD is disabled.
The AT89LP6440 is a fully-featured microcontroller that multiplexes several functions on its lim-
ited I/O pins. Some device functionality must be sacrificed to provide resources for On-Chip
Debugging. The On-Chip Debug System has the following limitations:
• P4.2/RST cannot be connected directly to V
• All external reset sources must be removed.
• If P4.3 needs to be debugged in systems using the crystal oscillator, the external clock option
• The Debug Clock pin (DCL) is physically located on that same pin as Port Pin P4.2 and the
must be removed.
should be selected. The quartz crystal and any capacitors on XTAL1 or XTAL2 must be
removed and an external clock signal must be driven on XTAL1. Some emulator systems may
provide a user-configurable clock for this purpose.
External Reset (RST). Therefore, neither P4.2 nor an external reset source may be emulated
when OCD is enabled.
DDA
DCL
P4.2/RST
XTAL1
GND
CLK = Internal RC
A
DCL
VDD
CLK = Crystal Oscillator
P4.2/RST
XTAL2
XTAL1
GND
C
DD
DCL
CLK
and any external capacitors connected to RST
VDD
P4.3
CLK = External Clock
P4.2/RST
XTAL1
GND
DDA
B
XTAL2
VDD
3706A–MICRO–9/09
DDA
Related parts for AT89LP6440-20PU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: