AT89LP6440-20PU Atmel, AT89LP6440-20PU Datasheet - Page 165
AT89LP6440-20PU
Manufacturer Part Number
AT89LP6440-20PU
Description
MCU 8051 64K FLASH ISP 40PDIP
Manufacturer
Atmel
Series
89LPr
Datasheet
1.AT89LP6440-20MU.pdf
(194 pages)
Specifications of AT89LP6440-20PU
Core Processor
8051
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
38
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Eeprom Size
8K x 8
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.4 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 165 of 194
- Download datasheet (6Mb)
25.8
Table 25-6.
25.9
25.9.1
3706A–MICRO–9/09
Address
0080H
User Signature and Analog Configuration
Programming Interface Timing
Power-up Sequence
Parameter Name
RC Oscillator Calibration Byte
Analog Configuration Definitions
The User Signature Array contains 256 bytes of non-volatile memory in two 128-byte pages. The
first page of the User Signature Array (0000H–007FH) is available for serial numbers, firmware
revision information, date codes or other user parameters. The User Signature Array may only
be written by an external device when the User Signature Programming Fuse is enabled. When
the fuse is enabled, Chip Erase will also erase the first page of the array. When the fuse is dis-
abled, the array is not affected by write or erase commands. Programming of the Signature
Array can also be disabled by the Lock Bits. However, reading the signature is always allowed
and the array should not be used to store security sensitive information. The User Signature
Array may be modified during execution through the In-Application Programming interface,
regardless of the state of the User Signature Programming fuse or Lock Bits, provided that the
IAP Fuse is enabled. Note that the address of the User Signature Array, as seen by the IAP
interface, equals the User Signature address plus 256 (0100H–01FFH instead of 0000H–
00FFH).
The second page of the User Signature Array (0080H–00FFH) contains analog configuration
parameters for the AT89LP6440. Each byte represents a parameter as listed in
is preset in the factory. The parameters are read at POR and the device is configured accord-
ingly. The second page of the array is not affected by Chip Erase. Other bytes in this page may
be used as additional signature space; however, care should be taken to preserve the parame-
ter values when modifying other bytes.
This section details general system timing sequences and constraints for entering or exiting In-
System Programming as well as parameters related to the Serial Peripheral Interface during
ISP. The general timing parameters for the following waveform figures are listed in section
ing Parameters” on page
Execute this sequence to enter programming mode immediately after power-up. In the RST pin
is disabled or if the ISP Fuse is disabled, this is the only method to enter programming (see
“External Reset” on page
1. Apply power between VDD and GND pins. RST should remain low.
2. Wait at least t
3. Wait at least t
4. Start programming session.
depend on the current settings of the device.
PWRUP
SUT
Description
The RC Calibration Byte controls the frequency of the internal RC oscillator. The
frequency is inversely proportional to the calibration value such that higher values
result in lower frequencies. A copy of the factory-set calibration value is stored at
location 0008H of the Atmel Signature.
for the internal Power-on Reset to complete. The value of t
. and drive SS high.
169.
34).
AT89LP6440 - Preliminary
Table 25-6
SUT
will
“Tim-
and
165
Related parts for AT89LP6440-20PU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: