ATMEGA8515-16PU Atmel, ATMEGA8515-16PU Datasheet - Page 181

• Manufacturer Part Number: ATMEGA8515-16PU
• Description: IC AVR MCU 8K 16MHZ 5V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8515-16PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Cpu Speed: 16 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 35
• Interface: SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 8K Bytes
• Timers: 1-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 2
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

Latching of Fuses
Signature Bytes
Calibration Byte
2512K–AVR–01/10
Table 84. Fuse Low Byte
Notes:
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are
locked if Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the
Lock bits.
The fuse values are latched when the device enters Programming mode and changes of
the fuse values will have no effect until the part leaves Programming mode. This does
not apply to the EESAVE Fuse which will take effect once it is programmed. The fuses
are also latched on Power-up in Normal mode.
All Atmel microcontrollers have a 3-byte signature code which identifies the device. This
code can be read in both Serial and Parallel mode, also when the device is locked. The
three bytes reside in a separate address space.
For the ATmega8515 the signature bytes are:
1. $000: $1E (indicates manufactured by Atmel).
2. $001: $93 (indicates 8KB Flash memory).
3. $002: $06 (indicates ATmega8515 device when $001 is $93).
The ATmega8515 stores four different calibration values for the internal RC Oscillator.
These bytes resides in the signature row high byte of the addresses 0x000, 0x0001,
0x0002, and 0x0003 for 1, 2, 4, and 8 MHz respectively. During Reset, the 1 MHz value
is automatically loaded into the OSCCAL Register. If other frequencies are used, the
calibration value has to be loaded manually, see “Oscillator Calibration Register – OSC-
CAL” on page 39 for details.
Fuse Low Byte
BODLEVEL
BODEN
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
1. The default value of SUT1..0 results in maximum start-up time. See Table 13 on page
2. The default setting of CKSEL3..0 results in internal RC Oscillator @ 1 MHz. See
39 for details.
Table 5 on page 35 for details.
Bit no
6
5
4
7
3
2
1
0
Description
Brown-out Detector trigger
level
Brown-out Detector enable
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
Default value
1 (unprogrammed)
1 (unprogrammed, BOD
disabled)
1 (unprogrammed)
0 (programmed)
0 (programmed)
0 (programmed)
0 (programmed)
1 (unprogrammed)
ATmega8515(L)
(1)
(2)
(2)
(2)
(1)
(2)
181