PIC18F2331-E/MM Microchip Technology, PIC18F2331-E/MM Datasheet - Page 235

• Manufacturer Part Number: PIC18F2331-E/MM
• Description: IC MCU FLASH 4KX16 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2331-E/MM

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-QFN
• Core: PIC
• Processor Series: PIC18F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Data Ram Size: 768 B
• Data Rom Size: 256 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 5
• Height: 0.88 mm
• Interface Type: EUSART, I2C, SPI, SSP
• Length: 6 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V, 5.8 V
• Supply Voltage (min): 3.9 V, 4.2 V
• Width: 6 mm
• For Use With: I3-DB18F4431 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Other names: PIC18F2331-E/ML; PIC18F2331-E/ML

20.4.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA<5>), or the Continuous Receive
Enable bit, CREN (RCSTA<4>). Data is sampled on the
RC7/RX/DT/SDO pin on the falling edge of the clock.
If enable bit SREN is set, only a single word is received.
If enable bit CREN is set, the reception is continuous
until CREN is cleared. If both bits are set, then CREN
takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 20-12:
 2010 Microchip Technology Inc.
Note:
RC7/RX/DT/SDO
RC6/TX/CK/SS
RC6/TX/CK/SS
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRGH
and BRG16 bits, as required, to achieve the
desired baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
(SCKP = 0)
(SCKP = 1)
(Interrupt)
CREN bit
SREN bit
SREN bit
RCIF bit
RXREG
Write to
Read
EUSART SYNCHRONOUS MASTER
RECEPTION
Timing diagram demonstrates Sync Master mode with SREN bit = 1 and BRGH bit = 0.
Pin
Pin
Pin
Q2
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘0’
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
bit 0
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 1
PIC18F2331/2431/4331/4431
bit 2
bit 3
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
Ensure bits, CREN and SREN, are clear.
If interrupts are desired, set enable bit, RCIE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
Interrupt flag bit, RCIF, will be set when
reception is complete and an interrupt will be
generated if the enable bit, RCIE, was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
bit, CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
bit 4
bit 5
bit 6
DS39616D-page 235
bit 7
Q1 Q2 Q3 Q4
‘0’