AT32UC3B1128-Z1UR Atmel, AT32UC3B1128-Z1UR Datasheet - Page 596
AT32UC3B1128-Z1UR
Manufacturer Part Number
AT32UC3B1128-Z1UR
Description
MCU AVR32 128K FLASH 48-QFN
Manufacturer
Atmel
Series
AVR®32 UC3r
Datasheet
1.AT32UC3B164-AUR.pdf
(680 pages)
Specifications of AT32UC3B1128-Z1UR
Package / Case
48-QFN Exposed Pad
Voltage - Supply (vcc/vdd)
1.65 V ~ 1.95 V
Operating Temperature
-40°C ~ 85°C
Speed
60MHz
Number Of I /o
28
Core Processor
AVR
Program Memory Type
FLASH
Ram Size
32K x 8
Program Memory Size
128KB (128K x 8)
Data Converters
A/D 6x10b
Oscillator Type
Internal
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Connectivity
I²C, IrDA, SPI, SSC, UART/USART, USB
Core Size
32-Bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 596 of 680
- Download datasheet (10Mb)
27.4.5.1
27.4.5.2
27.4.5.3
27.4.6
32059J–12/2010
JTAG Interface
I/O Lines
Power Management
Clocks
The TMS, TDI, and TDO pins are multiplexed with I/O lines. When the JTAG is used the associ-
ated pins must be enabled. To enable the JTAG pins, refer to
While using the multiplexed JTAG lines all normal peripheral activity on these lines is disabled.
The user must make sure that no external peripheral is blocking the JTAG lines while
debugging.
When an instruction that accesses the SAB is loaded in the instruction register, before entering
a sleep mode, the system clocks are not switched off to allow debugging in sleep modes. This
can lead to a program behaving differently when debugging.
The JTAG Interface uses the external TCK pin as clock source. This clock must be provided by
the JTAG master.
Instructions that use the SAB bus requires the internal main clock to be running.
The JTAG Interface is accessed through the dedicated JTAG pins shown in
595. The TMS control line navigates the TAP controller, as shown in
The TAP controller manages the serial access to the JTAG Instruction and Data registers. Data
is scanned into the selected instruction or data register on TDI, and out of the register on TDO,
in the Shift-IR and Shift-DR states, respectively. The LSB is shifted in and out first. TDO is high-
Z in other states than Shift-IR and Shift-DR.
The device implements a 5-bit Instruction Register (IR). A number of public JTAG instructions
defined by the JTAG standard are supported, as described in
ber of 32-bit AVR-specific private JTAG instructions described in
instruction selects a specific data register for the Shift-DR path, as described for each
instruction.
Section
Section
Figure 27-5 on page
27.4.7.
27.5.2, as well as a num-
Section
AT32UC3B
Table 27-6 on page
27.5.3. Each
597.
596
Related parts for AT32UC3B1128-Z1UR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: