DSPIC30F1010-20E/SP Microchip Technology, DSPIC30F1010-20E/SP Datasheet - Page 209

• Manufacturer Part Number: DSPIC30F1010-20E/SP
• Description: IC DSPIC MCU/DSP 6K 28DIP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F1010-20E/SP

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 6KB (2K x 24)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Frequency: 15MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 21
• Flash Memory Size: 6KB
• Supply Voltage Range: 3V To 5.5V
• Package: 28SPDIP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300023 - KIT DEMO DSPICDEM SMPS BUCKDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

18.4
The primary oscillator uses is shown in Figure 18-3.
FIGURE 18-3:
18.5
Two of the primary Oscillator modes use an external
clock. These modes are EC and EC with IO.
In the EC mode (Figure 18-4), the OSC1 pin can be
driven by CMOS drivers. In this mode, the OSC1 pin is
high-impedance and the OSC2 pin is the clock output
(F
synchronization purposes.
FIGURE 18-4:
FIGURE 18-5:
© 2006 Microchip Technology Inc.
OSC
/2). This output clock is useful for testing or
PRIMARY OSCILLATOR ON OSC1/
OSC2 PINS:
EXTERNAL CLOCK INPUT
Note 1: A series resistor, Rs, may be required for AT strip cut crystals.
Clock from Ext System
Clock from Ext System
PRIMARY OSCILLATOR
EXTERNAL CLOCK INPUT OPERATION (EC OSCILLATOR CONFIGURATION)
EXTERNAL CLOCK INPUT OPERATION (ECIO OSCILLATOR CONFIGURATION)
C1
2: The feedback resistor, R
C2
XTAL
Rs
(1)
F
OSC
I/O
OSC2/CLKO
OSC1/CLKI
/2
Preliminary
F
, is typically in the range of 2 to 10 M
OSC1
I/O (OSC2)
OSC1
OSC2
dsPIC30F
dsPIC30F
In the EC with IO mode (Figure 18-5), the OSC1 pin
can be driven by CMOS drivers. In this mode, the
OSC1 pin is high-impedance and the OSC2 pin
becomes a general purpose I/O pin. The feedback
device between OSC1 and OSC2 is turned off to save
current.
R
dsPIC30F1010/202X
F
(2)
CLKO/RC15
To CLKGEN
DS70178C-page 207