ATXMEGA128A1-C7U Atmel, ATXMEGA128A1-C7U Datasheet - Page 95
![MCU AVR 128K FLASH 1.6V 100VFBGA](/photos/12/32/123223/100-lfbga_sml.jpg)
ATXMEGA128A1-C7U
Manufacturer Part Number
ATXMEGA128A1-C7U
Description
MCU AVR 128K FLASH 1.6V 100VFBGA
Manufacturer
Atmel
Series
AVR® XMEGAr
Datasheet
1.ATAVRONEKIT.pdf
(113 pages)
Specifications of ATXMEGA128A1-C7U
Core Processor
AVR
Core Size
8/16-Bit
Speed
32MHz
Connectivity
EBI/EMI, I²C, IrDA, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
78
Program Memory Size
128KB (64K x 16)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
1.6 V ~ 3.6 V
Data Converters
A/D 16x12b, D/A 4x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-VFBGA
Processor Series
XMEGA
Core
AVR
Data Bus Width
8 bit, 16 bit
Data Ram Size
8 KB
Interface Type
SPI, TWI, USART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
78
Number Of Timers
8
Operating Supply Voltage
2.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATAVRISP2, ATAVRONEKIT, ATQT600
Minimum Operating Temperature
- 40 C
Operating Temperature Range
- 40 C to + 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
8067M–AVR–09/10
22. EEPROM page buffer always written when NVM DATA0 is written
23. Pending full asynchronous pin change interrupts will not wake the device
24. Pin configuration does not affect Analog Comparator Output
25. Low level interrupt triggered when pin input is disabled
26. JTAG enable does not override Analog Comparator B output
27. NMI Flag for Crystal Oscillator Failure automatically cleared
If the EEPROM is memory mapped, writing to NVM DATA0 will corrupt data in the EEPROM
page buffer.
Problem fix/Workaround
Before writing to NVM DATA0, for example when doing software CRC or flash page buffer
write, check if EEPROM page buffer active loading flag (EELOAD) is set. Do not write NVM
DATA0 when EELOAD is set.
Any full asynchronous pin-change Interrupt from pin 2, on any port, that is pending when the
sleep instruction is executed, will be ignored until the device is woken from another source
or the source triggers again. This applies when entering all sleep modes where the System
Clock is stopped.
Problem fix/Workaround
None.
The Output/Pull and inverted pin configuration does not affect the Analog Comparator out-
put function.
Problem fix/Workaround
None for Output/Pull configuration.
For inverted I/O, configure the Analog Comparator to give an inverted result (i.e. connect
positive input to the negative AC input and vice versa), or use and external inverter to
change polarity of Analog Comparator output.
If a pin input is disabled, but pin is configured to trigger on low level, interrupt request will be
sent.
Problem fix/Workaround
Ensure that Interrupt mask for the disabled pin is cleared.
When JTAG is enabled this will not override the Analog Comparator B (ACB) output,
AC0OUT on pin 7 if this is enabled.
Problem fix/Workaround
Use Analog Comparator output for ACA when JTAG is used, or use the PDI as debug
interface.
NMI flag for Crystal Oscillator Failure (XOSCFDIF) will be automatically cleared when exe-
cuting the NMI interrupt handler.
Problem fix/Workaround
This device revision has only one NMI interrupt source, so checking the interrupt source in
software is not required.
XMEGA A1
95