DSPIC30F2020-30I/MM Microchip Technology, DSPIC30F2020-30I/MM Datasheet - Page 11
![IC DSPIC MCU/DSP 12K 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
DSPIC30F2020-30I/MM
Manufacturer Part Number
DSPIC30F2020-30I/MM
Description
IC DSPIC MCU/DSP 12K 28QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.AC164335.pdf
(286 pages)
2.DM300023.pdf
(22 pages)
3.DM300023.pdf
(18 pages)
4.DSPIC30F2011-20ISO.pdf
(66 pages)
5.DSPIC30F2011-20IP.pdf
(26 pages)
6.DSPIC30F1010-30ISO.pdf
(26 pages)
7.DSPIC30F1010-30ISO.pdf
(50 pages)
Specifications of DSPIC30F2020-30I/MM
Core Processor
dsPIC
Core Size
16-Bit
Speed
30 MIPs
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-QFN
Core Frequency
15MHz
Core Supply Voltage
3.3V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
21
Flash Memory Size
12KB
Supply Voltage Range
3V To 3.6V
Package
28QFN-S EP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
30 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
21
Interface Type
I2C/SPI/UART
On-chip Adc
8-chx10-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM300023 - KIT DEMO DSPICDEM SMPS BUCKAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F2020-30I/MMB32
Manufacturer:
Microchip Technology
Quantity:
135
32. Module: MCLR Pin
EXAMPLE 1:
© 2008 Microchip Technology Inc.
; This function performs a clock-switch from FRC to FRC+PLL. All other oscillator
; settings remain unchanged.
; Filename: ClockSwitch.s
_ClockSwitch:
A brown-out event occurs when V
the minimum operating voltage for the device but
not all the way down to V
SMPS device is running with the PLL enabled and
a brown-out event occurs, the device may stop
running and the MCLR pin will not reset the device.
If this occurs, the device can only be reset by
cycling power to the V
It is recommended that an external Brown-out
Reset (BOR) circuit be used to hold the device in
reset during a brown-out event, to overcome this
problem. The external BOR circuit will use the
MCLR pin to hold the device in reset. The following
work around, in combination with the external BOR
circuit, will ensure that the device is cleanly reset
after a brown-out event occurs.
Work around
The dsPIC DSC SMPS device must be powered
up with the PLL disabled, the Fail-Safe Clock
Monitor enabled and Clock Switching enabled.
The PLL should be enabled in software via a clock
switch after the device is reset (refer to Section
29. “Oscillator” in the “dsPIC30F Family
Reference Manual” (DS70268) for details on clock
switching). This ensures that the MCLR pin is
functional and that the device can be reset by an
external BOR circuit (see Figure 1).
mov
mov
mov
mov
mov.b
mov.b
mov.b
mov
mov
mov
mov
mov.b
mov.b
mov.b
return
#OSCCON+1,w4
#0x0078, w0
#0x009A, w1
#0x0001, w2
w0, [w4]
w1, [w4]
w2, [w4]
#OSCCON,w4
#0x0046, w0
#0x0057, w1
#0x0001, w2
w0, [w4]
w1, [w4]
w2, [w4]
CLOCK SWITCHING EXAMPLE
DD
SS
pins.
. When the dsPIC DSC
; Get address of high OSCCON byte
; 1st password for high byte access to OSCCON
; 2nd password for low byte access to OSCCON
; NOSC value for FRC+PLL
; Write 1st password
; Write 2nd password
; Write NOSC value
; Get address of low OSCCON byte
; 1st password for high byte access to OSCCON
; 2nd password for low byte access to OSCCON
; Set OSWEN bit
; Write 1st password
; Write 2nd password
; Write OSWEN bit
DD
drops below
FIGURE 1:
*Any commercially available BOR circuit
can be used in this configuration. Refer to
the BOR circuit manufacturer’s data sheet
for exact circuit configuration.
dsPIC30F1010/202X
Use one of the following methods to achieve the
work around.
Method 1: Insert the code shown in Example 1 at
the start of the program.
Method 2: Call the code shown in Example 1 in
the beginning of code execution by including the
ClockSwitch.s file in the project and adding the
following code:
• For assembly programming, add the following
• For C programming, add the following
+5V
instruction at the beginning of the program:
instruction at the beginning of the program:
.global __reset
…
…
__reset:
rcall ClockSwitch
…
…
int main(void)
{
}
External
Circuit
BOR
U2*
ClockSwitch;
…
…
R*
U1
DS80319D-page 11
MCLR
V
SS
+5V