ST7FLITEU09M6 STMicroelectronics, ST7FLITEU09M6 Datasheet - Page 110

• Manufacturer Part Number: ST7FLITEU09M6
• Description: MCU 8BIT SGL VOLT FLASH SO-8
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITEU09M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 5
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: ST7FLITEUx
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: ICC
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7FLITU0-D/RAIS, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 5 Channel
• Cpu Family: ST7
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 128Byte
• # I/os (max): 5
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3.3V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SO N
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Electrical characteristics
Table 66.
1.
2. Configuration not recommended, all unused pins must be kept at a fixed voltage: using the output mode of the I/O for
3. The R
4. R
5. To generate an external interrupt, a minimum pulse width has to be applied on an I/O port pin configured as an external
Caution:
Note:
110/139
Symbol
t
t
t
example or an external pull-up or pull-down resistor (see
based on design simulation and technology characteristics, not tested in production. This value depends on V
temperature values.
Figure
interrupt source.
f(IO)out
r(IO)out
w(IT)in
Data based on characterization results, not tested in production.
C
PU
IO
not applicable on PA3 because it is multiplexed on RESET pin
PU
54).
pull-up equivalent resistor is based on a resistive transistor (corresponding I
I/O pin capacitance
Output high to low level fall
time
Output low to high level rise
time
External interrupt pulse time
(5)
General characteristics (continued)
Figure 52. Two typical applications with unused I/O pin
During normal operation the ICCCLK pin must be pulled- up, internally or externally
(external pull-up of 10k mandatory in noisy environment). This is to avoid entering ICC
mode unexpectedly during a reset
I/O can be left unconnected if it is configured as output (0 or 1) by the software. This has the
advantage of greater EMC robustness and lower cost.
Figure 53. Typical I
(1)
(1)
Parameter
V
DD
10k
PU
UNUSED I/O PORT
vs. V
60
50
40
30
20
10
0
C
Between 10% and 90%
ST7XXX
L
= 50 pF
DD
with V
-45°C
25°C
90°C
130°C
Conditions
Figure
IN
57). Static peak current value taken at a fixed V
=V
SS
Vdd [V]
10k
Min
UNUSED I/O PORT
PU
1
current characteristics described in
ST7XXX
ST7LITEU05 ST7LITEU09
Typ
25
25
5
Max
DD
IN
and
value,
t
Unit
CPU
pF
ns