ST7FLITEU09M6 STMicroelectronics, ST7FLITEU09M6 Datasheet - Page 83

• Manufacturer Part Number: ST7FLITEU09M6
• Description: MCU 8BIT SGL VOLT FLASH SO-8
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITEU09M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 5
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: ST7FLITEUx
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: ICC
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7FLITU0-D/RAIS, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 5 Channel
• Cpu Family: ST7
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 128Byte
• # I/os (max): 5
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3.3V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SO N
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / Rohs Status: Details

ST7LITEU05 ST7LITEU09
The total conversion time:
t
While the ADC is on, these two phases are continuously repeated.
At the end of each conversion, the sample capacitor is kept loaded with the previous
measurement load. The advantage of this behaviour is that it minimizes the current
consumption on the analog pin in case of single input channel measurement.
A/D conversion
The analog input ports must be configured as input, no pull-up, no interrupt. Refer to the “I/O
ports” chapter. Using these pins as analog inputs does not affect the ability of the port to be
read as a logic input.
In the ADCCSR register:
●
ADC conversion mode
In the ADCCSR register:
Set the ADON bit to enable the A/D converter and to start the conversion. From this time on,
the ADC performs a continuous conversion of the selected channel.
When a conversion is complete:
●
●
A read to the ADCDRH or a write to any bit of the ADCCSR register resets the EOC bit.
To read the 10 bits, perform the following steps:
1.
2.
3.
To read only 8 bits, perform the following steps:
1.
2.
Changing the conversion channel
The application can change channels during conversion.
When software modifies the CH[2:0] bits in the ADCCSR register, the current conversion is
stopped, the EOC bit is cleared, and the A/D converter starts converting the newly selected
channel.
CONV =
cycles) and the C
the optimum analog to digital conversion accuracy.
Select the CS[2:0] bits to assign the analog channel to convert.
The EOC bit is set by hardware.
The result is in the ADCDR registers.
Poll EOC bit
Read ADCDRL
Read ADCDRH. This clears EOC automatically.
Poll EOC bit
Read ADCDRH. This clears EOC automatically.
t
SAMPLE
+ t
HOLD
ADC
sample capacitor is disconnected from the analog input pin to get
On-chip peripherals
83/139