ST7FLIT10BY0M6 STMicroelectronics, ST7FLIT10BY0M6 Datasheet - Page 111

no-image

ST7FLIT10BY0M6

Manufacturer Part Number
ST7FLIT10BY0M6
Description
IC MCU 8BIT 2K FLASH 16-SOIC
Manufacturer
STMicroelectronics
Series
ST7r
Datasheet

Specifications of ST7FLIT10BY0M6

Core Processor
ST7
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
11
Program Memory Size
2KB (2K x 8)
Program Memory Type
FLASH
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 7x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
16-SOIC (0.300", 7.5mm Width)
Processor Series
ST7FLIT1x
Core
ST7
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
SPI
Maximum Clock Frequency
8 MHz
Number Of Programmable I/os
17
Number Of Timers
4
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Development Tools By Supplier
ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 7 Channel
For Use With
497-5049 - KIT STARTER RAISONANCE ST7FLITE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
 Details
13.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
13.2.1 Voltage Characteristics
13.2.2 Current Characteristics
13.2.3 Thermal Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to V
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7kΩ for
RESET, 10kΩ for I/Os). Unused I/O pins must be tied in the same way to V
2. I
respected, the injection current must be limited externally to the I
while a negative injection is induced by V
corresponding V
3. All power (V
4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout
the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:
- Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage
is lower than the specified limits)
- Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as
far as possible from the analog input pins.
5. No negative current injection allowed on PB0 pin.
6. When several inputs are submitted to a current injection, the maximum ΣI
and negative injected currents (instantaneous values). These results are based on characterisation with ΣI
mum current injection on four I/O port pins of the device.
INJ(PIN)
I
INJ(PIN)
ΣI
V
V
V
Symbol
Symbol
Symbol
ESD(HBM)
DD
INJ(PIN)
ESD(MM)
T
I
I
V
VDD
VSS
must never be exceeded. This is implicitly insured if V
I
STG
T
IO
- V
IN
J
2) & 4)
DD
SS
2)
IN
) and ground (V
maximum must always be respected
Supply voltage
Input voltage on any pin
Electrostatic discharge voltage (Human Body Model)
Electrostatic discharge voltage (Machine Model)
Total current into V
Total current out of V
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on ISPSEL pin
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on PB0 pin
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
Storage temperature range
Maximum junction temperature (see
page
147)
SS
) lines must always be connected to the external supply.
IN
<V
DD
SS
SS
. For true open-drain pads, there is no positive injection current, and the
power lines (source)
Ratings
Ratings
Ratings
ground lines (sink)
1) & 2)
DD
5)
or V
6)
SS
could damage the device if an unintentional internal reset
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
Table 24, “THERMAL CHARACTERISTICS,” on
INJ(PIN)
IN
maximum is respected. If V
3)
3)
value. A positive injection is induced by V
DD
or V
INJ(PIN)
6)
SS
according to their reset configuration.
see
is the absolute sum of the positive
V
Maximum value
Maximum value
SS
section 13.7.3 on page 128
-0.3 to V
-65 to +150
Value
± 20
- 25
150
7.0
± 5
± 5
± 5
± 5
+5
75
20
40
IN
DD
maximum cannot be
+0.3
ST7LITE1xB
INJ(PIN)
Unit
Unit
Unit
111/159
mA
°C
IN
V
>V
maxi-
DD

Related parts for ST7FLIT10BY0M6