ST7FLITE35F2B6 STMicroelectronics, ST7FLITE35F2B6 Datasheet - Page 104

• Manufacturer Part Number: ST7FLITE35F2B6
• Description: IC MCU 8BIT 8K FLASH 20DIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE35F2B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ST7FLITE3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5085 - EVAL BOARD UNIV MOTOR CONTROL497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Function Descriptions
104/235
}
#endif
/*==========================================================
==========================================================*/
/* Communication mode defined as ITDRV_WITHOUTBUF_RX in
ST7lib_config.h */
/* Single byte reception */
#ifdef I2C_ITDRV_WITHOUTBUF_RX
I2C_Generate_Start ();
while(!((I2C_IsTransmitCompleted())== I2C_START_OK));
I2C_Load_Address (Addr_Byte_Tx, I2C_RX_MODE);
Timeoutcount = 0 ;
Temp1 = I2C_IsTransmitCompleted() ;
while ((User_Timeout_Function()) && ( Temp1 != I2C_ADD_TX_OK))
{
}
switch (Temp1)
{
}
Timeoutcount = 0 ;
Temp2 = I2C_IsReceptionCompleted() ;
while ((User_Timeout_Function()) && ((Temp2) == I2C_RX_DATA_EMPTY) )
{
}
if (User_Timeout_Function())
{
Reception through ‘Interrupt driven without buffer’ mode
}
I2C_Generate_Stop ();
while (!(I2C_IsStopGen ())) ;
Temp1 = I2C_IsTransmitCompleted() ;
case I2C_TX_AF:
default:
Temp2 = I2C_IsReceptionCompleted() ;
switch (Temp2)
{
}
User_Function();
break;
break;
case I2C_RX_ARLO:
case I2C_RX_BERR:
case I2C_DATA_RX_OK:
case I2C_DATA_TX_OK:
default:
Rx_Data =I2C_GetByte ();
User_Function();
break;
User_Function();
break;
break;
User_Function();
break;
/* If none of the above condition is true */
/* To check address transmission status */
/* Waits for data byte reception */
/* Transmission successful */
/* Error Management */