STM8L151K4T6 STMicroelectronics, STM8L151K4T6 Datasheet - Page 62

• Manufacturer Part Number: STM8L151K4T6
• Description: IC MCU 8BIT 16KB FLASH 32LQFP
• Manufacturer: STMicroelectronics
• Series: STM8L EnergyLiter

Specifications of STM8L151K4T6

• Core Processor: STM8
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, IR, POR, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 22x12b, D/A 1x12
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: STM8L15x
• Core: STM8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 30
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWSTM8
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 22 Channel
• On-chip Dac: 12 bit, 1 Channel
• For Use With: 497-10594 - DEM FOR STM8L15X LOW PWR MODES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10515

Electrical parameters
62/122
Table 15.
1. Positive injection is not possible on these I/Os. V
2. I
3. When several inputs are submitted to a current injection, the maximum ΣI
Table 16.
Symbol
never be exceeded. A negative injection is induced by V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
positive and negative injected currents (instantaneous values). These results are based on
characterization with ΣI
INJ(PIN)
T
ΣI
Symbol
I
STG
INJ(PIN)
T
INJ(PIN)
I
I
J
VDD
VSS
I
IO
must never be exceeded. This is implicitly insured if V
Current characteristics
Thermal characteristics
Storage temperature range
Maximum junction temperature
Total current into V
Total current out of V
Output current sunk by IR_TIM pin (with high sink LED
driver capability)
Output current sunk by any other I/O and control pin
Output current sourced by any I/Os and control pin
Injected current on true open-drain pins (PC0 and PC1)
Injected current on FT pins (PA7 and PE0)
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
INJ(PIN)
IN
>V
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Doc ID 15962 Rev 5
Ratings
DD
SS
power line (source)
ground line (sink)
Ratings
IN
maximum must always be respected. I
(2)
IN
<V
SS
IN
.
maximum is respected. If V
(1)
INJ(PIN)
IN
STM8L151xx, STM8L152xx
<V
INJ(PIN)
(3)
SS
-65 to +150
(1)
is the absolute sum of the
.
value. A positive
Min
150
INJ(PIN)
Max.
± 25
- 25
± 5
- 5
- 5
80
80
80
25
IN
maximum
must
Unit
Unit
° C
mA