STM32F103T8U6 STMicroelectronics, STM32F103T8U6 Datasheet - Page 58

• Manufacturer Part Number: STM32F103T8U6
• Description: MCU 32BIT ARM 64K FLASH 36VFQFPN
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103T8U6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 36-VFQFN, 36-VFQFPN
• Processor Series: STM32F103x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 20 KB
• Interface Type: CAN/I2C/SPI/USART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ST-LINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10-ch x 12-bit)
• Controller Family/series: (ARM Cortex) STM32
• No. Of I/o's: 26
• Ram Memory Size: 20KB
• Cpu Speed: 72MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 12
• Rohs Compliant: Yes
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical characteristics
5.3.12
Table 34.
1. FT = 5V tolerant. To sustain a voltage higher than V
2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization, not tested in production.
3. With a minimum of 100 mV.
4. Leakage could be higher than max. if negative current is injected on adjacent pins.
5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
58/96
Symbol
V
R
R
C
V
V
I
MOS/NMOS contribution
lkg
hys
PU
PD
IH
IO
IL
Standard I/O input low level
voltage
I/O FT
Standard I/O input high level
voltage
I/O FT
Standard IO Schmitt trigger
voltage hysteresis
IO FT Schmitt trigger voltage
hysteresis
Input leakage current
Weak pull-up equivalent
resistor
Weak pull-down equivalent
resistor
I/O pin capacitance
I/O port characteristics
General input/output characteristics
Unless otherwise specified, the parameters given in
performed under the conditions summarized in
compliant.
I/O static characteristics
All I/Os are CMOS and TTL compliant (no software configuration required). Their
characteristics cover more than the strict CMOS-technology or TTL parameters. The
coverage of these requirements is shown in
in
Figure 27
(1)
(1)
(5)
(5)
input low level voltage
input high level voltage
(2)
Parameter
to the series resistance is minimum
and
(2)
(4)
Figure 28
for 5 V tolerant I/Os.
V
Standard I/Os
SS
Conditions
Doc ID 13587 Rev 12
V
V
V

IN
I/O FT
IN
DD
IN
V


= 5 V
+0.5 the internal pull-up/pull-down resistors must be disabled.
IN
V
V
(~10% order)

DD
SS
V
DD
0.41 (V
Figure 25
0.42 (V
.
5% V
Table
–0.5
–0.5
Min
200
DD
30
30
DD
DD
Table 34
–2)+1.3
9. All I/Os are CMOS and TTL
–2)+1
(3)
and
Figure 26
STM32F103x8, STM32F103xB
are derived from tests
Typ
40
40
5
0.32 (V
0.28 (V
for standard I/Os, and
V
DD
Max
DD
5.5
DD
1
50
50
3
+0.5
–2)+0.75
–2)+0.8
Unit
mV
mV
µA
k
k
pF
V