MC908GZ16MFAE Freescale Semiconductor, MC908GZ16MFAE Datasheet - Page 250

• Manufacturer Part Number: MC908GZ16MFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ16MFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: ESCI, SPI, UART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface (SPI) Module
MODFEN — Mode Fault Enable Bit
SPR1 and SPR0 — SPI Baud Rate Select Bits
17.13.3 SPI Data Register
The SPI data register consists of the read-only receive data register and the write-only transmit data
register. Writing to the SPI data register writes data into the transmit data register. Reading the SPI data
register reads data from the receive data register. The transmit data and receive data registers are
separate registers that can contain different values. See
R7–R0/T7–T0 — Receive/Transmit Data Bits
250
This read/write bit, when set to 1, allows the MODF flag to be set. If the MODF flag is set, clearing the
MODFEN does not clear the MODF flag. If the SPI is enabled as a master and the MODFEN bit is low,
then the SS pin is available as a general-purpose I/O.
If the MODFEN bit is set, then this pin is not available as a general-purpose I/O. When the SPI is
enabled as a slave, the SS pin is not available as a general-purpose I/O regardless of the value of
MODFEN. See
If the MODFEN bit is low, the level of the SS pin does not affect the operation of an enabled SPI
configured as a master. For an enabled SPI configured as a slave, having MODFEN low only prevents
the MODF flag from being set. It does not affect any other part of SPI operation. See
Error.
In master mode, these read/write bits select one of four baud rates as shown in
SPR0 have no effect in slave mode. Reset clears SPR1 and SPR0.
Use this formula to calculate the SPI baud rate:
where:
CGMOUT = base clock output of the clock generator module (CGM)
BD = baud rate divisor
Address: $0012
Do not use read-modify-write instructions on the SPI data register since the
register read is not the same as the register written.
Reset:
Read:
Write:
17.12.4 SS (Slave Select).
Bit 7
R7
T7
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
Table 17-4. SPI Master Baud Rate Selection
Baud rate
SPR1 and SPR0
Figure 17-16. SPI Data Register (SPDR)
R6
T6
6
00
01
10
11
=
R5
T5
5
CGMOUT
------------------------- -
2
×
BD
NOTE
Unaffected by reset
R4
T4
4
Baud Rate Divisor (BD)
Figure
R3
T3
3
17-3.
128
32
2
8
R2
T2
2
R1
T1
1
Table
Freescale Semiconductor
17.7.2 Mode Fault
Bit 0
R0
T0
17-4. SPR1 and