MC908GZ16MFAE Freescale Semiconductor, MC908GZ16MFAE Datasheet - Page 81

• Manufacturer Part Number: MC908GZ16MFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ16MFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: ESCI, SPI, UART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

LVISTOP — LVI Enable in Stop Mode Bit
LVIRSTD — LVI Reset Disable Bit
LVIPWRD — LVI Power Disable Bit
LVI5OR3 — LVI 5-V or 3-V Operating Mode Bit
SSREC — Short Stop Recovery Bit
STOP — STOP Instruction Enable Bit
Freescale Semiconductor
When the LVIPWRD bit is clear, setting the LVISTOP bit enables the LVI to operate during stop mode.
Reset clears LVISTOP.
LVIRSTD disables the reset signal from the LVI module. See
LVIPWRD disables the LVI module. See
LVI5OR3 selects the voltage operating mode of the LVI module (see
(LVI)). The voltage mode selected for the LVI should match the operating V
Electrical
SSREC enables the CPU to exit stop mode with a delay of 32 CGMXCLK cycles instead of a
4096-CGMXCLK cycle delay.
If the system clock source selected is the internal oscillator or the external crystal and the
OSCENINSTOP configuration bit is not set, the oscillator will be disabled during stop mode. The short
stop recovery does not provide enough time for oscillator stabilization and for this reason the SSREC
bit should not be set.
The system stabilization time for power-on reset and long stop recovery (both 4096 CGMXCLK cycles)
gives a delay longer than the LVI enable time for these startup scenarios. There is no period where the
MCU is not protected from a low-power condition. However, when using the short stop recovery
configuration option, the 32-CGMXCLK delay must be greater than the LVI’s turn on time to avoid a
period in startup where the LVI is not protecting the MCU.
STOP enables the STOP instruction.
1 = LVI enabled during stop mode
0 = LVI disabled during stop mode
1 = LVI module resets disabled
0 = LVI module resets enabled
1 = LVI module power disabled
0 = LVI module power enabled
1 = LVI operates in 5-V mode
0 = LVI operates in 3-V mode
1 = Stop mode recovery after 32 CGMXCLK cycles
0 = Stop mode recovery after 4096 CGMXCLCK cycles
1 = STOP instruction enabled
0 = STOP instruction treated as illegal opcode
Specifications) for the LVI’s voltage trip points for each of the modes.
The LVI5OR3 bit is cleared by a power-on reset (POR) only. Other resets
will leave this bit unaffected.
Exiting stop mode by an LVI reset will result in the long stop recovery.
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
Chapter 11 Low-Voltage Inhibit
NOTE
NOTE
Chapter 11 Low-Voltage Inhibit
Chapter 11 Low-Voltage Inhibit
(LVI).
DD
(see
Functional Description
Chapter 21
(LVI).
81