DF3048X16V Renesas Electronics America, DF3048X16V Datasheet - Page 628

• Manufacturer Part Number: DF3048X16V
• Description: MCU 5V 128K,PB-FREE 100-TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300Hr

Specifications of DF3048X16V

• Core Processor: H8/300H
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Section 19 Flash Memory (H8/3048F: Dual Power Supply (V
7. During reset (when RES pin input is Low), if MD
8. Regarding 12 V application to the V
Notes: 1. Mode pin input must satisfy the mode programming setup time (t
19.4.2
When set to user program mode, the H8/3048F can erase and program its flash memory by
executing a user program. On-board updates of the on-chip flash memory can be carried out by
providing on-board circuits for supplying V
the program area.
To select user program mode, select a mode that enables the on-chip ROM (mode 5, 6, or 7) and
apply 12 V to the V
would in mode 5, 6, or 7, except for the flash memory. A watchdog timer overflow, however,
cannot output a reset signal while 12 V is applied to V
bit (RSTOE) should not be set to 1.
The flash memory cannot be read while being programmed or erased, so the update program must
either be stored in external memory, or transferred temporarily to the RAM area and executed in
RAM.
Rev. 7.00 Sep 21, 2005 page 602 of 878
REJ09B0259-0700
versa, by instantaneous transfer to 5 V input, the personal computer switches to operation
mode. As a result, the address port or bus control output signal (AS, RD, HWR, LWR) status
changes, so do not these pins as output signals during reset, as the personal computer internal
section needs to be shut down.
exceed the maximum rating of 13 V. Also, be sure to connect bypass capacitors to the V
MD
boot mode will not operate correctly. In addition, during boot program operation or writing
and erasing the flash memory, do not interrupt V
2
2. For notes on applying and cutting V
pins *
User Program Mode
the reset release timing. When 12 V is applied to or disconnected from the MD
delay occurs in the fall and rise waveforms due to the influence of the pull-up/pull-
down resistor connected to the MD
delay must be confirmed with the actual waveform on the board.
Programming and Erasing Precautions (Dual-Power Supply).”
1
.
PP
pin. In this mode, the on-chip peripheral modules operate as they normally
PP
and MD
PP
and data, and storing an update program in part of
2
PP
pin, etc. For reset release timing, therefore, this
, refer to 19.8, note (4) of “Flash Memory
2
pins, insure that peak overshoot does not
2
PP
pin input changes from 0 V to 12 V or vice
PP
. The watchdog timer’s reset output enable
*
2
.
PP
= 12 V))
MDS
) with respect to
2
pin, a
pp
and