ATMEGA8515-16AI Atmel, ATMEGA8515-16AI Datasheet - Page 198

• Manufacturer Part Number: ATMEGA8515-16AI
• Description: IC AVR MCU 8K 16MHZ IND 44-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8515-16AI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Data Converters: -

DC Characteristics (Continued)
T
Notes:
198
A
Symbol
I
V
I
t
CC
ACLK
ACPD
ACIO
= -40°C to 85°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (20 mA at V
5. Minimum V
ATmega8515(L)
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 200 mA.
2] The sum of all IOL, for ports B0 - B7, D0 - D7, and XTAL2, should not exceed 100 mA.
3] The sum of all IOL, for ports A0 - A7, E0 - E2, and C0 - C7 should not exceed 100 mA.
conditions (non-transient),the following must be observed:
1] The sum of all IOH,for all ports, should not exceed 200 mA.
2] The sum of all IOH,for ports B0 - B7, D0 - D7, and XTAL2,should not exceed 100 mA.
3] The sum of all IOH,for ports A0 - A7, E0 - E2, and C0 - C7 should not exceed 100 mA.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
CC
for Power-down is 2.5V.
= 2.7V to 5.5V (Unless Otherwise Noted)
(5)
Condition
Active 4 MHz, V
(
Active 8 MHz, V
(
Idle 4 MHz, V
(
Idle 8 MHz, V
(
WDT enabled, V
WDT disabled, V
V
V
V
V
V
V
ATmega8515
ATmega8515
ATmega8515
ATmega8515
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
L)
)
L)
)
CC
CC
CC
= 3V
= 5V
CC
= 3V
= 5V
= 3V
= 3V
Min
-50
CC
CC
= 5V, 10 mA at V
= 5V, 10 mA at V
Typ
750
500
CC
CC
Max
< 13
1.5
5.5
< 2
12
40
50
4
= 3V) under steady state
= 3V) under steady state
2512K–AVR–01/10
Units
mA
mA
mA
mA
mV
µA
µA
nA
ns