PIC18F4539T-E/ML Microchip Technology, PIC18F4539T-E/ML Datasheet - Page 152

• Manufacturer Part Number: PIC18F4539T-E/ML
• Description: IC PIC MCU FLASH 12KX16 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4539T-E/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 24KB (12K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1408 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-QFN
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1408 B
• Interface Type: I2C, SPI, AUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DV164005, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18FXX39
16.4.6.1
The master device generates all of the serial clock
pulses and the START and STOP conditions. A trans-
fer is ended with a STOP condition, or with a Repeated
START condition. Since the Repeated START condi-
tion is also the beginning of the next serial transfer, the
I
In Master Transmitter mode, serial data is output
through SDA, while SCL outputs the serial clock. The
first byte transmitted contains the slave address of the
receiving device (7 bits) and the Read/Write (R/W) bit.
In this case, the R/W bit will be logic '0'. Serial data is
transmitted 8 bits at a time. After each byte is transmit-
ted, an Acknowledge bit is received. START and STOP
conditions are output to indicate the beginning and the
end of a serial transfer.
In Master Receive mode, the first byte transmitted con-
tains the slave address of the transmitting device
(7 bits) and the R/W bit. In this case, the R/W bit will be
logic '1'. Thus, the first byte transmitted is a 7-bit slave
address followed by a '1' to indicate the receive bit.
Serial data is received via SDA, while SCL outputs the
serial clock. Serial data is received 8 bits at a time. After
each byte is received, an Acknowledge bit is transmit-
ted. START and STOP conditions indicate the
beginning and end of transmission.
The baud rate generator used for the SPI mode opera-
tion is used to set the SCL clock frequency for either
100 kHz, 400 kHz or 1 MHz I
Section 16.4.7 (“Baud Rate Generator”), for more
detail.
DS30485A-page 150
2
C bus will not be released.
I
2
C Master Mode Operation
2
C operation. See
Preliminary
A typical transmit sequence would go as follows:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. The MSSP module generates an interrupt at the
11. The user generates a STOP condition by setting
12. Interrupt is generated once the STOP condition
The user generates a START condition by set-
ting
(SSPCON2<0>).
SSPIF is set. The MSSP module will wait the
required start time before any other operation
takes place.
The user loads the SSPBUF with the slave
address to transmit.
Address is shifted out the SDA pin until all 8 bits
are transmitted.
The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
The user loads the SSPBUF with eight bits of
data.
Data is shifted out the SDA pin until all 8 bits are
transmitted.
The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
SSPCON2 register (SSPCON2<6>).
end of the ninth clock cycle by setting the SSPIF
bit.
the STOP enable bit PEN (SSPCON2<2>).
is complete.
the
START
 2002 Microchip Technology Inc.
enable
bit,
SEN