DSPIC30F6014A-20I/PT Microchip Technology, DSPIC30F6014A-20I/PT Datasheet - Page 158

• Manufacturer Part Number: DSPIC30F6014A-20I/PT
• Description: IC DSPIC MCU/DSP 144K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6014A-20I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 144KB (48K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPDM300004-2 - BOARD DEMO DSPICDEM.NET 2DM300004-1 - BOARD DEMO DSPICDEM.NET 1AC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Other names: DSPIC30F6014A20IP

dsPIC30F6011A/6012A/6013A/6014A
Concurrently, the POR time-out (T
time-out (T
Reset is released. If T
is being used, then a nominal delay of T
is
(T
The BOR status bit (RCON<1>) will be set to indicate
that a BOR has occurred. The BOR circuit, if enabled,
will continue to operate while in Sleep or Idle modes
and will reset the device should V
threshold voltage.
DS70143B-page 156
POR
applied.
+ T
FSCM
PWRT
The
).
) will be applied before the internal
total
PWRT
delay
= 0 and a crystal oscillator
DD
POR
in
fall below the BOR
) and the PWRT
this
FSCM
= 100 s
case
Preliminary
is
FIGURE 20-6:
Note:
Note 1: External Power-on Reset circuit is
2: R should be suitably chosen so as to
3: R1 should be suitably chosen so as to
Dedicated supervisory devices, such as
the MCP1XX and MCP8XX, may also be
used as an external Power-on Reset
circuit.
required only if the V
is too slow. The diode D helps discharge
the capacitor quickly when V
down.
make sure that the voltage drop across
R does not violate the device’s electrical
specification.
limit any current flowing into MCLR from
external capacitor C, in the event of
MCLR/V
trostatic Discharge (ESD) or Electrical
Overstress (EOS).
D
V
DD
R
C
PP
EXTERNAL POWER-ON
RESET CIRCUIT (FOR
SLOW V
© 2005 Microchip Technology Inc.
pin breakdown due to Elec-
R1
DD
DD
dsPIC30F
MCLR
POWER-UP)
power-up slope
DD
powers