DSPIC30F4013T-20I/PT Microchip Technology, DSPIC30F4013T-20I/PT Datasheet - Page 131

• Manufacturer Part Number: DSPIC30F4013T-20I/PT
• Description: IC DSPIC MCU/DSP 48K 44TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F4013T-20I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, POR, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 48KB (16K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• For Use With: AC30F006 - MODULE SKT FOR DSPIC30F 44TQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: DSPIC30F4013T20IP

FIGURE 19-3:
19.12 Configuring Analog Port Pins
The use of the ADPCFG and TRIS registers control the
operation of the A/D port pins. The port pins that are
desired as analog inputs must have their correspond-
ing TRIS bit set (input). If the TRIS bit is cleared (out-
put), the digital output level (V
converted.
The A/D operation is independent of the state of the
CH0SA<3:0>/CH0SB<3:0> bits and the TRIS bits.
When reading the Port register, all pins configured as
analog input channels will read as cleared.
Pins configured as digital inputs will not convert an ana-
log input. Analog levels on any pin that is defined as a
digital input (including the ANx pins) may cause the
input buffer to consume current that exceeds the
device specifications.
 2004 Microchip Technology Inc.
RAM Contents:
Read to Bus:
Signed Fractional
Signed Integer
Fractional
Integer
A/D OUTPUT DATA FORMATS
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d11 d11 d11 d11 d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
0
OH
or V
0
OL
0
Advance Information
) will be
0
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
19.13 Connection Considerations
The analog inputs have diodes to V
protection. This requires that the analog input be
between V
range by greater than 0.3V (either direction), one of the
diodes becomes forward biased and it may damage the
device if the input current specification is exceeded.
An external RC filter is sometimes added for anti-
aliasing of the input signal. The R component should be
selected to ensure that the sampling time requirements
are satisfied. Any external components connected (via
high impedance) to an analog input pin (capacitor,
zener diode, etc.) should have very little leakage
current at the pin.
dsPIC30F3014/4013
DD
and V
SS
. If the input voltage exceeds this
0
0
DD
DS70138C-page 129
and V
0
0
0
0
SS
as ESD
0
0