CY8C26643-24PI Cypress Semiconductor Corp, CY8C26643-24PI Datasheet - Page 135

• Manufacturer Part Number: CY8C26643-24PI
• Description: IC MCU 16K FLASH 256B 48-DIP
• Manufacturer: Cypress Semiconductor Corp
• Series: PSOC™ CY8C26xxxr

Specifications of CY8C26643-24PI

• Core Processor: M8C
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: SPI, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 44
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.25 V
• Data Converters: A/D 1x8b, 1x11b, 1x12b; D/A 1x9b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-DIP (0.600", 15.24mm)
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Applications: CapSense
• Technology: CMOS
• Processing Unit: Microcontroller
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.25V
• Package Type: PDIP
• Screening Level: Industrial
• Pin Count: 48
• Mounting: Through Hole
• Rad Hardened: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant
• Other names: 428-1432; 428-1432-5; 428-1432

13.2.8
Table 114:
1.
2.
September 5, 2002
I
V
V
I
I
V
V
Flash
Flash
Flash
ccp
ilp
ihp
olv
ohv
ilp
ihp
Symbol
Driving internal pull-down resistor.
A maximum of 36 x 50,000 block endurance cycles is allowed. This may be balanced between operations on 36x1
blocks of 50,000 maximum cycles each, 36x2 blocks of 25,000 maximum cycles each, or 36x4 blocks of 12,500
maximum cycles each (and so forth to limit the total number of cycles to 36x50,000 and that no single block ever
sees more than 50,000 cycles).
The CY8C25xxx/26xxx family of PSoC devices uses an adaptive algorithm to enhance endurance over the indus-
trial temperature range (-40°C to +85°C ambient). Any temperature range within a 50°C span between 0°C and
85°C is considered constant with respect to endurance enhancements. For instance, if room temperature (25°C)
is the nominal operating temperature, then the range from 0°C to 50°C can be approximated by the constant value
25 and a temperature sensor is not needed.
For the full industrial range, the user must employ a temperature sensor User Module (FlashTemp) and feed the
result to the temperature argument before writing. Refer to the Flash APIs Application Note AN2015 at http://
www.cypressmicro.com under Support or Active Design Support for more information.
enpb
ent
dr
DC Programming Specifications
DC Programming Specifications
Supply Current During Programming or Verify
Input Low Voltage During Programming or Verify
Input High Voltage During Programming or Verify
Input Current when Applying Vilp to P1[0] or P1[1]
During Programming or Verify
Input Current when Applying Vihp to P1[0] or
P1[1] During Programming or Verify
Output Low Voltage During Programming or Verify -
Output High Voltage During Programming or
Verify
Flash Endurance (Per Block)
Flash Endurance (Total)
Flash Data Retention (After Cycling)
DC Programming Specifications
Document #: 38-12010 CY Rev. ** CMS Rev. 3.20
2
-
-
2.2
-
-
V
50,000
1,800,000
10
Minimum
cc
- 1.0
5
-
-
-
-
-
-
-
-
Typical
Maximum
20
0.8
-
0.2
1.5
V
V
-
-
ss
cc
DC and AC Characteristics
1
+ 0.75 V
mA
V
V
mA
mA
V
E/W Cycles
per Block
E/W Cycles
Years
Unit
135