MC68HC908GT16CFB Freescale Semiconductor, MC68HC908GT16CFB Datasheet - Page 154

• Manufacturer Part Number: MC68HC908GT16CFB
• Description: IC MCU 16K FLASH 8MHZ SPI 44PQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GT16CFB

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 36
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Enhanced Serial Communications Interface (ESCI) Module
To initiate an ESCI transmission:
At the start of a transmission, transmitter control logic automatically loads the transmit shift register with
a preamble of 1s. After the preamble shifts out, control logic transfers the SCDR data into the transmit
shift register. A 0 start bit automatically goes into the least significant bit (LSB) position of the transmit shift
register. A 1 stop bit goes into the most significant bit (MSB) position.
The ESCI transmitter empty bit, SCTE, in SCS1 becomes set when the SCDR transfers a byte to the
transmit shift register. The SCTE bit indicates that the SCDR can accept new data from the internal data
bus. If the ESCI transmit interrupt enable bit, SCTIE, in SCC2 is also set, the SCTE bit generates a
transmitter CPU interrupt request.
When the transmit shift register is not transmitting a character, the TxD pin goes to the idle condition,
logic 1. If at any time software clears the ENSCI bit in ESCI control register 1 (SCC1), the transmitter and
receiver relinquish control of the port E pins.
14.4.2.3 Break Characters
Writing a 1 to the send break bit, SBK, in SCC2 loads the transmit shift register with a break character.
For TXINV = 0 (output not inverted), a transmitted break character contains all 0s and has no start, stop,
or parity bit. Break character length depends on the M bit in SCC1 and the LINR bits in SCBR. As long as
SBK is at 1, transmitter logic continuously loads break characters into the transmit shift register. After
software clears the SBK bit, the shift register finishes transmitting the last break character and then
transmits at least one 1. The automatic 1 at the end of a break character guarantees the recognition of
the start bit of the next character.
When LINR is cleared in SCBR, the ESCI recognizes a break character when a start bit is followed by
eight or nine 0 data bits and a 0 where the stop bit should be, resulting in a total of 10 or 11 consecutive
0 data bits. When LINR is set in SCBR, the ESCI recognizes a break character when a start bit is followed
by 9 or 10 0 data bits and a 0 where the stop bit should be, resulting in a total of 11 or 12 consecutive 0
data bits.
Receiving a break character has these effects on ESCI registers:
14.4.2.4 Idle Characters
For TXINV = 0 (output not inverted), a transmitted idle character contains all 1s and has no start, stop, or
parity bit. Idle character length depends on the M bit in SCC1. The preamble is a synchronizing idle
character that begins every transmission.
154
1. Enable the ESCI by writing a 1 to the enable ESCI bit (ENSCI) in ESCI control register 1 (SCC1).
2. Enable the transmitter by writing a 1 to the transmitter enable bit (TE) in ESCI control register 2
3. Clear the ESCI transmitter empty bit (SCTE) by first reading ESCI status register 1 (SCS1) and
4. Repeat step 3 for each subsequent transmission.
•
•
•
•
•
•
(SCC2).
then writing to the SCDR. For 9-bit data, also write the T8 bit in SCC3.
Sets the framing error bit (FE) in SCS1
Sets the ESCI receiver full bit (SCRF) in SCS1
Clears the ESCI data register (SCDR)
Clears the R8 bit in SCC3
Sets the break flag bit (BKF) in SCS2
May set the overrun (OR), noise flag (NF), parity error (PE),
or reception in progress flag (RPF) bits
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
Freescale Semiconductor