C8051F133 Silicon Laboratories Inc, C8051F133 Datasheet - Page 191

• Manufacturer Part Number: C8051F133
• Description: IC 8051 MCU 64K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F13xr

Specifications of C8051F133

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 100MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Data Bus Width: 8 bit
• Data Ram Size: 8.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 100 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit to 12 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No
• Other names: 336-1150

14.7. Phase-Locked Loop (PLL)
A Phase-Locked-Loop (PLL) is included, which is used to multiply the internal oscillator or an external
clock source to achieve higher CPU operating frequencies. The PLL circuitry is designed to produce an
output frequency between 25 MHz and 100 MHz, from a divided reference frequency between 5 MHz and
30 MHz. A block diagram of the PLL is shown in Figure 14.2.
14.7.1. PLL Input Clock and Pre-divider
The PLL circuitry can derive its reference clock from either the internal oscillator or an external clock
source. The PLLSRC bit (PLL0CN.2) controls which clock source is used for the reference clock (see SFR
Definition 14.5). If PLLSRC is set to ‘0’, the internal oscillator source is used. Note that the internal oscilla-
tor divide factor (as specified by bits IFCN1-0 in register OSCICN) will also apply to this clock. When
PLLSRC is set to ‘1’, an external oscillator source will be used. The external oscillator should be active and
settled before it is selected as a reference clock for the PLL circuit. The reference clock is divided down
prior to the PLL circuit, according to the contents of the PLLM4-0 bits in the PLL Pre-divider Register
(PLL0DIV), shown in SFR Definition 14.6.
14.7.2. PLL Multiplication and Output Clock
The PLL circuitry will multiply the divided reference clock by the multiplication factor stored in the
PLL0MUL register shown in SFR Definition 14.7. To accomplish this, it uses a feedback loop consisting of
a phase/frequency detector, a loop filter, and a current-controlled oscillator (ICO). It is important to config-
ure the loop filter and the ICO for the correct frequency ranges. The PLLLP3–0 bits (PLL0FLT.3–0) should
be set according to the divided reference clock frequency. Likewise, the PLLICO1–0 bits (PLL0FLT.5–4)
should be set according to the desired output frequency range. SFR Definition 14.8 describes the proper
settings to use for the PLLLP3–0 and PLLICO1–0 bits. When the PLL is locked and stable at the desired
frequency, the PLLLCK bit (PLL0CN.5) will be set to a ‘1’. The resulting PLL frequency will be set accord-
ing to the equation:
Where “Reference Frequency” is the selected source clock frequency, PLLN is the PLL Multiplier, and
PLLM is the PLL Pre-divider.
Oscillator
Oscillator
External
Internal
Figure 14.2. PLL Block Diagram
0
1
PLL0DIV

Reference
Divided
Clock
Rev. 1.4
Frequency
Detection
PLL0CN
Phase /
C8051F120/1/2/3/4/5/6/7
PLL0MUL
Loop Filter

PLL0FLT
C8051F130/1/2/3
Controlled
Oscillator
Current
PLL Clock
Output
191