XC705B32CFNE Freescale Semiconductor, XC705B32CFNE Datasheet - Page 228

• Manufacturer Part Number: XC705B32CFNE
• Description: IC MCU 2.1MHZ 32K OTP 52-PLCC
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of XC705B32CFNE

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SCI
• Peripherals: POR, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: OTP
• Eeprom Size: 256 x 8
• Ram Size: 528 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x8b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

14
F.5
Oscillator divide-by-two is forced in bootstrap mode.
The 432 bytes of self-check firmware on the MC68HC05B6 are replaced by 576 bytes of bootstrap
firmware. A detailed description of the modes of operation within bootstrap mode is given below.
The bootstrap program in mask ROM address locations $0200 to $024F and $3E00 to $3FEF can
be used to program the EPROM and the EEPROM, to check if the EPROM is erased or to load
and execute data in RAM.
After reset, while going to the bootstrap mode, the vector located at address $3FEE and $3FEF
(RESET) is fetched to start execution of the bootstrap program. To place the part in bootstrap
mode, the IRQ pin should be at 2xV
pin from low to high. The hold time on the IRQ and TCAP1 pins is two clock cycles after the
external RESET pin is brought high.
When the MC68HC705B16N is placed in the bootstrap mode, the bootstrap reset vector will be
fetched and the bootstrap firmware will start to execute.
to enter each level of bootstrap mode on the rising edge of RESET.
The bootstrap program will first copy part of itself in RAM (except ‘RAM parallel load’), as the
program cannot be executed in ROM during verification/programming of the EPROM. It will then
set the TCMP1 output to a logic high level, unlike the MC68HC05B6 which keeps TCMP1 low. This
can be used to distinguish between the two circuits and, in particular, for selection of the VPP level
and current capability.
Freescale
F-10
x = Don’t care
V
IRQ pin
SS
2xV
2xV
2xV
2xV
2xV
2xV
to V
DD
DD
DD
DD
DD
DD
DD
TCAP1 pin PD1 PD2 PD3 PD4
V
Bootstrap mode
SS
V
V
V
V
V
V
to V
DD
DD
DD
DD
DD
DD
DD
x
0
0
1
1
1
x
Table F-4 Mode of operation selection
x
0
0
0
0
0
0
0
1
0
1
0
1
x
DD
MC68HC705B16N
with the TCAP1 pin ‘high’ during transition of the RESET
0
0
0
0
1
1
x
Single chip
Erased EPROM verification
EPROM verification;
EPROM verification; erase EEPROM;
EPROM/EEPROM parallel program/verify
Erased EPROM verification; erase EEPROM;
EPROM parallel program/verify (no E
Jump to start of RAM ($0051); SEC bit = NON ACTIVE
Serial RAM load/execute – similar to MC68HC05B6 but can fill RAM I
and II
Table F-4
shows the conditions required
Mode
2
)
MC68HC05B6
Rev. 4.1