LM2902N STMicroelectronics, LM2902N Datasheet - Page 12

• Manufacturer Part Number: LM2902N
• Description: IC OP AMP LP QUAD 14-DIP
• Manufacturer: STMicroelectronics

Specifications of LM2902N

• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Slew Rate: 0.4 V/µs
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 20nA
• Voltage - Input Offset: 2000µV
• Current - Supply: 1.5mA
• Current - Output / Channel: 20mA
• Voltage - Supply, Single/dual (±): 3 V ~ 30 V, ±1.5 V ~ 15 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: 14-DIP (0.300", 7.62mm)
• Number Of Channels: 4
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 7 mV
• Input Bias Current (max): 150 nA
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 1.2 mA
• Maximum Power Dissipation: 500 mW
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Dual Supply Voltage: +/- 3 V, +/- 5 V, +/- 9 V, +/- 12 V
• Maximum Dual Supply Voltage: +/- 15 V
• Minimum Dual Supply Voltage: +/- 1.5 V
• Mounting Style: Through Hole
• Shutdown: No
• Supply Voltage (max): 30 V
• Supply Voltage (min): 3 V
• Technology: Bipolar
• Voltage Gain Db: 100 dB
• Bandwidth: 1.3 MHz
• Channel Separation: 120
• Common Mode Rejection Ratio: 80
• Current, Input Bias: 20 nA
• Current, Input Offset: 2 nA
• Current, Output: 40 mA
• Current, Supply: 1.5 mA
• Harmonic Distortion: 0.015 %
• Number Of Amplifiers: Quad
• Package Type: DIP-14
• Signal Gain: 100 V/mV
• Temperature, Operating, Range: -40 to +125 °C
• Voltage, Input: -0.3 to +32 V
• Voltage, Noise: 40 nV/sqrt Hz
• Voltage, Offset: 2 mV
• Voltage, Output, High: 28 V
• Voltage, Output, Low: 5 mV
• Voltage, Supply: 3 to 30 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-1558-5

Package information
6
6.1
12/16
Package information
In order to meet environmental requirements, ST offers these devices in ECOPACK
packages. These packages have a lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com.
DIP14 package information
Figure 28. DIP14 package mechanical drawing
Table 4.
Ref.
a1
b1
e3
B
D
E
b
e
F
L
Z
I
DIP14 package mechanical data
Min.
0.51
1.39
1.27
Millimeters
15.24
Typ.
0.25
2.54
0.5
8.5
3.3
Max.
1.65
2.54
7.1
5.1
20
0.020
0.055
0.050
Min.
Inches
0.020
0.010
0.335
0.100
0.600
0.130
Typ.
0.065
0.787
0.280
0.201
0.100
Max.
LM2902
®