X40030S14IZ-B Intersil, X40030S14IZ-B Datasheet - Page 16

• Manufacturer Part Number: X40030S14IZ-B
• Description: IC VOLTAGE MONITOR TRPL 14-SOIC
• Manufacturer: Intersil
• Type: Multi-Voltage Supervisorr

Specifications of X40030S14IZ-B

• Number Of Voltages Monitored: 3
• Output: Push-Pull, Totem Pole
• Reset: Active High
• Reset Timeout: Adjustable/Selectable
• Voltage - Threshold: 1.8V, 2.6V, 4.4V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Equivalent Input Circuit for VxMON (x = 1, 2, 3)
Capacitance
DC Operating Characteristics
NOTES:
THIRD SUPPLY MONITOR
4. The device enters the Active state after any start, and remains active until: 9 clock cycles later if the Device Select Bits in the Slave Address
5. The device goes into Standby: 200ns after any stop, except those that initiate a high voltage write cycle; t
6. V
7. At +25°C, V
8. See ordering information for standard programming levels. For custom programmed levels, contact factory.
9. Based on characterization data.
SYMBOL
(Note 8)
(Note 9)
(Note 8)
(Note 9)
V
V
SYMBOL
t
t
Byte are incorrect; 200ns after a stop ending a read operation; or t
voltage cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave Address Byte.
RPD2
RPD3
TRIP2
TRIP3
I
C
V3
IL
C
OUT
Min. and V
IN
ΔV
V2MON Trip Point Voltage Range
V
V3MON Current
V3MON Trip Point Voltage Range
V
TRIP2
TRIP3
CC
Output Capacitance (SDA, RESET/RESET, LOWLINE, V2FAIL,V3FAIL, WDO)
Input Capacitance (SCL, WP, MR)
IH
= 3V
Max. are for reference only and are not tested.
to V2FAIL
to V3FAIL
V
ref
16
PARAMETER
VxMON
Over the recommended operating conditions, unless otherwise specified. (Continued)
X40030, X40031, X40034, X40035
PARAMETER
R
C
V
REF
X40030, X40031
X40034, X40035
X40030, X40031-A
X40030, X40031-B
X40030, X40031-C
X40034, X40035-A and B
X40034, X40035-C
X40030, X40031
X40034, X40035-A
X40034, X40035-B and C
WC
after a stop ending a write operation.
TEST CONDITIONS
t
RPDX
+
–
= 5µs WORST CASE
OUTPUT PIN
TEST CONDITIONS
V
V
OUT
(Note 3)
IN
2.85
2.55
2.15
1.25
0.95
1.65
3.05
2.85
MIN
1.7
0.9
1.7
= 0V
= 0V
WC
after a stop that initiates a high
(Note 7)
TYP
2.9
2.6
2.2
1.3
1.0
1.7
3.1
2.9
ΔV = 100mV
(Note 3)
MAX
8
6
(Note 3)
MAX
4.75
2.95
2.65
2.25
1.35
1.05
4.75
1.75
3.15
2.95
3.5
15
5
5
August 25, 2008
UNIT
FN8114.2
pF
pF
UNIT
µA
µs
µs
V
V
V
V
V
V
V
V
V
V
V