71M6511-IGT/F Maxim Integrated Products, 71M6511-IGT/F Datasheet - Page 63
![IC ENERGY METER RESIDENT 64-LQFP](/photos/37/63/376302/landingpageteridian6511_sml.jpg)
71M6511-IGT/F
Manufacturer Part Number
71M6511-IGT/F
Description
IC ENERGY METER RESIDENT 64-LQFP
Manufacturer
Maxim Integrated Products
Datasheet
1.71M6511H-IGTF.pdf
(98 pages)
Specifications of 71M6511-IGT/F
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71M6511-IGT/F
Manufacturer:
ST
Quantity:
1 500
Company:
Part Number:
71M6511-IGT/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
OPT_TXDIS
PREBOOT
PRE_SAMPS[1:0]
RTC_SEC[5:0]
RTC_MINI[5:0]
RTC_HR[4:0]
RTC_DAY[2:0]
RTC_DATE[4:0]
RTC_MO[3:0]
RTC_YR[7:0]
RTC_DEC_SEC
RTC_INC_SEC
RTM_EN
RTM0[7:0]
RTM1[7:0]
RTM2[7:0]
RTM3[7:0]
SECURE
SSI_EN
SSI_10M
SSI_CKGATE
SSI_FSIZE[1:0]
SSI_FPOL
Page: 63 of 98
A Maxim Integrated Products Brand
2008[5]
SFR
B2[7]
2001[7:6]
2015
2016
2017
2018
2019
201A
201B
201C[1]
201C[0]
2002[3]
2060
2061
2062
2063
SFR
B2[6]
2070[7]
2070[6]
2070[5]
2070[4:3]
2070[2]
© 2005–2010 Teridian Semiconductor Corporation
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
W
R/
W
R/
W
W
R
output.
Tristates the OPT_TX output.
Indicates that the preboot sequence is active.
Together w/ SUM_CYCLES, this value determines the number of
samples in one sum cycle between XFER interrupts for the CE.
Number of samples = PRE_SAMPS*SUM_CYCLES.
The RTC interface. These are the ‘year’, ‘month’, ‘day’, ‘hour’,
‘minute’ and ‘second’ parameters for the RTC. The RTC is set by
writing to these registers. Year 00 is defined as a leap year.
RTC time correction bits. Only one bit may be pulsed at a time. When
pulsed, causes the RTC time value to be incremented (or
decremented) by an additional second the next time the RTC_SEC
register is clocked. The pulse width may be any value. If an additional
correction is desired, the MPU must wait 2 seconds before pulsing
one of the bits again.
Real Time Monitor enable. When ‘0’, the RTM output is low. This bit
enables the two wire version of RTM
Four RTM probes. Before each CE code pass, the values of these
registers are serially output on the RTM pin. The RTM registers are
ignored when RTM_EN=0.
Enables security provisions that prevent external reading of flash
memory and CE program RAM. This bit is reset on chip reset and
may only be set. Attempts to write zero are ignored.
Enables the Synchronous Serial Interface (SSI) on SEG3, SEG4, and
SEG5 pins. If SSI_RDYEN is set, SEG6 is enabled also. The pins take
on the new functions SCLK, SSDATA, SFR, and SRDY, respectively.
When SSI_EN is high and LCD_EN is low, these pins are converted to
the SSI function, regardless of LCDEN and LCD_NUM. For proper
LCD operation, SSI_EN must not be high when LCD_EN is high.
SSI clock speed: 0: 5MHz, 1: 10MHz
SSI gated clock enable. When low, the SCLK is continuous. When
high, the clock is held low when data is not being transferred.
SSI frame pulse format:
0: once at beginning of SSI sequence (whole block of data),
1: every 8 bits, 2: every 16 bits, 3: every 32 bits.
SFR pulse polarity: 0: positive, 1: negative
SEC 00 to 59
MIN
HR
DAY 01 to 07 (01=Sunday)
DATE 01 to 31
MO
YR
00-42, 01-50, 10-84, 11-100
Single-Phase Energy Meter IC
00 to 59
00 to 23 (00=Midnight)
01 to 12
00 to 256
71M6511/71M6511H
DATA SHEET
NOVEMBER 2010
V2.7