78M6612-IGTR/F Maxim Integrated Products, 78M6612-IGTR/F Datasheet - Page 77
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
78M6612-IGTR/F
Manufacturer Part Number
78M6612-IGTR/F
Description
IC POWER MEASUREMENT AC 64-LQFP
Manufacturer
Maxim Integrated Products
Datasheet
1.78M6612-IMF.pdf
(111 pages)
Specifications of 78M6612-IGTR/F
Mounting Style
SMD/SMT
Package / Case
LQFP-64
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
78M6612-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
DS_6612_001
Rev. 1.2
Name
DIO_DIR1[7:6, 3:0]
DIO_DIR2[5:3,2:1]
DIO_0[7:1]*
DIO_1[7:6,3:0]
DIO_2[5:3,1:0]
DIO_EEX[1:0]
DIO_PV
DIO_PW
EEDATA[7:0]
EECTRL[7:0]
ECK_DIS
EQU[2:0]
EX_XFR
EX_RTC
EX_FWCOL
EX_PLL
FIR_LEN
Location
SFR91
[7:6,3:0]
SFRA1
[5:3,2:1]
SFR80
[7:1]
SFR90
[7:6,3:0]
SFRA0
[5:3,1:0]
2008[7:6]
2008[2]
2008[3]
SFR9E
SFR9F
2005[5]
2000[7:5]
2002[0]
2002[1]
2007[4]
2007[5]
2005[4]
Rst
30
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Wk
30
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Dir
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Description
Programs the direction of pins DIO15-DIO14, DIO11-DIO8.
1 indicates output. Ignored if the pin is not configured as
I/O.
Programs the direction of pins DIO20- DIO19 and DIO17-
DIO16 (and DIO21 for the 68 QFN package). 1 indicates
output. Ignored if the pin is not configured as I/O.
The value on the pins DIO7-DIO1. DIO3 is only available
on the 68-pin package. Pins configured as LCD will read
zero. When written, changes data on pins configured as
outputs. Pins configured as LCD or input will ignore write
operations.
The value on the pins DIO15-DIO14 and DIO11-DIO8.
Pins configured as LCD will read zero. When written,
changes data on pins configured as outputs. Pins
configured as LCD or input will ignore write operations.
The value on the pins DIO20-DIO19, and DIO17-DIO16
(and DIO21 for the 68 QFN package). Pins configured as
LCD will read zero. When written, changes data on pins
configured as outputs. Pins configured as LCD or input
will ignore write operations.
When set, converts DIO4 and DIO5 to interface with
external EEPROM. DIO4 becomes SDCK and DIO5
becomes bi-directional SDATA. LCD_NUM must be less
than or equal to 18.
Causes VARPULSE to be output on DIO7, if DIO7 is
configured as output. LCD_NUM must be less than 15.
Causes WPULSE to be output on DIO6, if DIO6 is
configured as output. LCD_NUM must be less than 16.
Serial EEPROM interface data.
Serial EEPROM interface control.
and thus preclude Flash erase and programming
operations. If ECK_ENA is set, it should be done at least
1000 ms after power-up to give emulators and
programming devices enough time to complete an erase
operation.
Specifies the power equation to be used by the CE.
Interrupt enable bits. These bits enable the XFER_BUSY,
the RTC_1SEC, the FirmWareCollision, and PLL
interrupts. Note that if one of these interrupts is to be
enabled, its corresponding EX enable bit must also be
set. See the Interrupts section for details.
The length of the ADC decimation FIR filter.
When FIR_LEN=1, the ADC has 2.370370x higher gain.
DIO_EEX[1:0]
Emulator clock disable. When one, the emulator
00
01
10
11
inhibit access to the part with the ICE interface
clock is disabled. This bit is to be used with
caution! Inadvertently setting this bit will
1-384 cycles, 0-288 cycles
Function
Disable EEPROM interface
2-Wire EEPROM interface
3-Wire EEPROM interface
Not used
78M6612 Data Sheet
77