XBIB-U Digi International/Maxstream, XBIB-U Datasheet - Page 30

• Manufacturer Part Number: XBIB-U
• Description: BOARD USB ZIGBEE MOD PRO
• Manufacturer: Digi International/Maxstream

Specifications of XBIB-U

• Design Resources: XBIB-U Shematic
• Accessory Type: Interface Board
• For Use With/related Products: XBee and XBee Pro Radios
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Sleep (Low Power)
Table 3‐04. XBee/XBee‐PRO Commands ‐ Sleep (Low Power)
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
Serial Interfacing
Table 3‐05. XBee‐PRO Commands ‐ Serial Interfacing
XBee/XBee‐PRO™ OEM RF Modules ‐ 802.15.4 ‐ v1.xAx [2007.05.031]
AT
Command
SM
ST
SP
DP (1.x80*)
AT
Command
BD
RO
AP (v1.x80*)
NB
Command
Category
Sleep
(Low Power)
Sleep
(Low Power)
Sleep
(Low Power)
Sleep
(Low Power)
Command
Category
Serial
Interfacing
Serial
Interfacing
Serial
Interfacing
Serial
Interfacing
Name and Description
Sleep Mode. <NonBeacon firmware> Set/Read Sleep Mode configurations.
Time before Sleep. <NonBeacon firmware> Set/Read time period of inactivity (no
serial or RF data is sent or received) before activating Sleep Mode. ST parameter is
only valid with Cyclic Sleep settings (SM = 4 - 5).
Coordinator and End Device ST values must be equal.
Also note, the GT parameter value must always be less than the ST value. (If GT > ST,
the configuration will render the module unable to enter into command mode.) If the ST
parameter is modified, also modify the GT parameter accordingly.
Cyclic Sleep Period. <NonBeacon firmware> Set/Read sleep period for cyclic sleeping
remotes. Coordinator and End Device SP values should always be equal. To send
Direct Messages, set SP = 0.
End Device - SP determines the sleep period for cyclic sleeping remotes. Maximum
sleep period is 268 seconds (0x68B0).
Coordinator - If non-zero, SP determines the time to hold an indirect message before
discarding it. A Coordinator will discard indirect messages after a period of (2.5 * SP).
Disassociated Cyclic Sleep Period. <NonBeacon firmware>
End Device - Set/Read time period of sleep for cyclic sleeping remotes that are
configured for Association but are not associated to a Coordinator. (i.e. If a device is
configured to associate, configured as a Cyclic Sleep remote, but does not find a
Coordinator, it will sleep for DP time before reattempting association.) Maximum sleep
period is 268 seconds (0x68B0). DP should be > 0 for NonBeacon systems.
Name and Description
Interface Data Rate. Set/Read the serial interface data rate for communications
between the RF module serial port and host.
Request non-standard baud rates with values above 0x80 using a terminal window.
Read the BD register to find actual baud rate achieved.
Packetization Timeout. Set/Read number of character times of inter-character delay
required before transmission. Set to zero to transmit characters as they arrive instead of
buffering them into one RF packet.
API Enable. Disable/Enable API Mode.
Parity. Set/Read parity settings.
© 2007 MaxStream, Inc.
Chapter 3 ‐ RF Module Configuration
Parameter Range
0 - 5
1 - 0xFFFF [x 1 ms]
0 - 0x68B0 [x 10 ms]
1 - 0x68B0 [x 10 ms]
Parameter Range
0 - 7 (standard baud rates)
0x80 - 0x1C200
(non-standard baud rates)
0 - 0xFF [x character times]
0 - 2
0 - 4
0 = No Sleep
1 = Pin Hibernate
2 = Pin Doze
3 = Reserved
4 = Cyclic sleep remote
5 = Cyclic sleep remote
6 = [Sleep Coordinator] for
0 = 1200 bps
1 = 2400
2 = 4800
3 = 9600
4 = 19200
5 = 38400
6 = 57600
7 = 115200
0 = Disabled
1 = API enabled
2 = API enabled
0 = 8-bit (no parity or
1 = 8-bit even
2 = 8-bit odd
3 = 8-bit mark
4 = 8-bit space
backwards compatibility
w/ v1.x6 only; otherwise,
use CE command.
(w/escaped control
w/ pin wake-up
7-bit (any parity)
characters)
Default
0
0x1388
(5000d)
0x3E8
(1000d)
Default
3
3
0
0
0
30