XB24-BPDK Digi International/Maxstream, XB24-BPDK Datasheet - Page 74

• Manufacturer Part Number: XB24-BPDK
• Description: KIT DEVELOPMENT XBEE SERIES 2
• Manufacturer: Digi International/Maxstream
• Series: XBee™r
• Type: 802.15.4/Zigbeer

Specifications of XB24-BPDK

• Frequency: 2.4GHz
• For Use With/related Products: XBee™ Series 2 Modules
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Security
RF Interfacing
1. Node types that support the command: C = Coordinator, R = Router, E = End Device
Serial Interfacing (I/O)
XBee ZNet 2.5/XBee‐PRO ZNet 2.5 ZigBee OEM RF Modules v1.x4x
Table 7‐04. Security Commands
Table 7‐05. RF Interfacing Commands
Table 7‐06. Serial Interfacing Commands
AT
Command
EE
EO
KY
AT
Command
PL
PM
DB
AT
Command
AP
AO
BD
2
2
Name and Description
Encryption Enable. Set/Read the encryption enable setting.
Encryption Options. Configure options for encryption. Unused option bits should be set
to 0. Options include:
0x01 - Send the security key unsecured over-the-air during joins
0x02 - Use trust center
Encryption Key. Set the 128-bit AES encryption key. This command is read-only; KY
cannot be read.
Name and Description
Power Level. Select/Read the power level at which the RF module transmits conducted
power.
Power Mode. Set/read the power mode of the device. Enabling boost mode will improve
the receive sensitivity by 1dB and increase the transmit power by 2dB
Note: Enabling boost mode on the XBee-PRO will not affect the output power. Boost
mode imposes a slight increase in current draw. See section 1.2 for details.
Received Signal Strength. This command reports the received signal strength of the
last received RF data packet. The DB command only indicates the signal strength of the
last hop. It does not provide an accurate quality measurement for a multihop link. DB
can be set to 0 to clear it.
Name and Description
API Enable. Enable API Mode.
The AP parameter is only applicable when using modules that contain the following
firmware versions:1.1xx (coordinator), 1.3xx (router/end device)
API Options. Configure options for API. Current options select the type of receive API
frame to send out the Uart for received RF data packets.
Interface Data Rate. Set/Read the serial interface data rate for communication between
the module serial port and host.
Any value above 0x07 will be interpreted as an actual baud rate. When a value above
0x07 is sent, the closest interface data rate represented by the number is stored in the
BD register.
© 2008 Digi International, Inc.
Node
Type
CRE
CRE
CRE
Node
Type
CRE
CRE
Node
Type
CRE
CRE
CRE
1
1
1
Parameter Range
0 - Encryption disabled
1 - Encryption enabled
0 - 0xFF
0 -
0xFFFFFFFFFFFFFFFF
Parameter Range
XBee
(boost mode disabled)
0 = -8 dBm
1 = -4 dBm
2 = -2 dBm
3 = 0 dBm
4 = +2 dBm
XBee-PRO
4 = 18 dBm
XBee-PRO
(International Variant)
4 = 10dBm
0-1,
0= -Boost mode disabled,
1= Boost mode enabled. 1
Parameter Range
1 - 2
0 - Default receive API
indicators enabled
1 - Explicit Rx data
indicator API frame
enabled (0x91)
0 - 7
(standard baud rates)
0x80 - 0x38400
(non-standard rates)
1 = API-enabled
2 = API-enabled
0 = 1200 bps
1 = 2400
2 = 4800
3 = 9600
4 = 19200
5 = 38400
6 = 57600
7 = 115200
(w/escaped control
characters)
Default
0
0
Default
4
Default
1
0
3
73