XB24-BPDK Digi International/Maxstream, XB24-BPDK Datasheet - Page 90
XB24-BPDK
Manufacturer Part Number
XB24-BPDK
Description
KIT DEVELOPMENT XBEE SERIES 2
Manufacturer
Digi International/Maxstream
Series
XBee™r
Type
802.15.4/Zigbeer
Datasheet
1.XB24-BPDK.pdf
(91 pages)
Specifications of XB24-BPDK
Frequency
2.4GHz
For Use With/related Products
XBee™ Series 2 Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 90 of 91
- Download datasheet (2Mb)
ZigBee Command Set
API / AT Firmware Versions
Appendix C: Migrating from the 802.15.4
Modified Commands
New Commands
802.15.4 application:
Also, refer to the “Getting Started” section for more information.
The 802.15.4 firmware supports the AP command for setting the module into No API (AP=0), API
without escaping (AP=1), or API with escaping (AP=2) modes. The first digit in the 802.15.4
firmware versions is a '1'.
The ZigBee firmware comes in different versions to support the API interface (AP 1, 2 modes) or
the AT command set (AP 0 mode). The first digit in the ZigBee firmware versions is an '8'.
The following is a list of firmware versions:
This following are some of the differences in the ZigBee firmware assuming familiarity with the
© 2008 Digi International, Inc.
• ZigBee Command Set
• Address Assignment
• API / AT Firmware Versions
• CH - Read Only command that displays the operating channel that was selected from SC.
• MY - Read Only command that displays the assigned 16-bit network address of the device.
• AI - ZigBee definitions added to this command. See documentation.
• A1, A2 and CE commands are not supported.
• NJ (Node Join Time) - This value determines how long a Coordinator or Router will allow other
• MP (16-bit Parent Network Address). This value represents the 16-bit parent network address
• BH (Broadcast Hops). This value sets the maximum number of hops for each broadcast data
• 1.0xx - Coordinator, AT Command support (Transparent Mode)
• 1.1xx - Coordinator, API support (AP 1, 2)
• 1.2xx - Router, End Device, AT Command support (Transparent Mode)
• 1.3xx - Router, End Device, API support (AP 1, 2)
devices to join to it. This command is supported on Coordinators & Routers only.
of the module.
transmission. Setting this to 0 will use the maximum number of hops.
Protocol
89
Related parts for XB24-BPDK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEV ZIGBEE
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
KIT STARTER XBEE
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
KIT DEV PRO ZIGBEE
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 1MW W/WIRE ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 1MW W/U.FL CONN
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 SER 2 CHIP ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 1MW W/CHIP ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 SER 2 U.FL CONN
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 SER 2 WIRE ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 SER 2 W/RPSMA
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 100MW CHIP ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 RS-232 ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
CONN CBL RPSMA MALE-N1 MALE 1FT
Manufacturer:
Digi International/Maxstream
Part Number:
Description:
CONN CBL RPSMA MALE-N1 MALE 4FT
Manufacturer:
Digi International/Maxstream
Part Number:
Description:
MODULE 9P 8MB SDRAM 4MB FLASH
Manufacturer:
Digi International/Maxstream
Datasheet: