ATA5812-PLQ Atmel, ATA5812-PLQ Datasheet - Page 6

• Manufacturer Part Number: ATA5812-PLQ
• Description: IC TXRX UHF ASK/FSK 1CH 48-QFN
• Manufacturer: Atmel

Specifications of ATA5812-PLQ

• Frequency: 315MHz
• Data Rate - Maximum: 20kbps
• Modulation Or Protocol: ASK, FSK
• Applications: Access Control, AMR, RKE
• Sensitivity: -116dBm
• Voltage - Supply: 2.4 V ~ 3.6 V or 4.4 V ~ 6 V
• Current - Receiving: 10.5mA
• Current - Transmitting: 10.5mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Power - Output: -
• Memory Size: -
• Other names: ATA5812-PLQTR

2. Typical Key Fob or Sensor Application with 1 Battery
Figure 2-1.
6
ATA5811/ATA5812
Typical RKE Key Fob or Sensor Application, 433.92 MHz, 1 Battery
Loop antenna
AVCC
C
10
Figure 2-1
external components are 11 capacitors, 1 resistor, 2 inductors and a crystal. C
voltage supply blocking capacitors. C
capacitor used for the internal quasi peak detector and for the highpass frequency of the data fil-
ter. C
of about 5.6 nH to 56 nH. L
crystal is integrated. R
antenna’s quality factor is somewhat reduced by this application due to the quality factor of L
and the RX/TX switch. On the other hand, this lower quality factor is necessary to have a robust
design with a bandwidth that is broad enough for production tolerances. Due to the single-ended
and ground-referenced design, the loop antenna can be a free-form wire around the application
as it is usually employed in RKE uni-directional systems. The ATA5811/ATA5812 provides suffi-
cient isolation and robust pulling behavior of internal circuits from the supply voltage as well as
an integrated VCO inductor to allow this. Since the efficiency of a loop antenna is proportional to
the square of the surrounded area it is beneficial to have a large loop around the application
board with a lower quality factor to relax the tolerance specification of the RF components and to
get a high antenna efficiency in spite of their lower quality factor.
L
2
L
1
7
C
to C
5
C
C
shows a typical 433.92 MHz RKE key fob or sensor application with one battery The
11
C
8
9
11
are RF matching capacitors in the range of 1 pF to 33 pF. L1 is a matching inductor
R
1
C
7
NC
NC
NC
RF_IN
NC
433_N868
NC
R_PWR
PWR_H
RF_OUT
NC
NC
1
is typically 22 k and sets the output power to about 5.5 dBm. The loop
2
C
C
is a feed inductor of about 120 nH. A load capacitor of 9 pF for the
1
2
ATA5811/ATA5812
+ Lithium cell
5
is a 10 nF supply blocking capacitor. C
C
4
SDO_TMDO
DEM_OUT
SDI_TMDI
N_RESET
CDEM
VSINT
RSSI
SCK
CLK
IRQ
CS
NC
C
13.25311 MHz
6
XTAL2
C
3
Microcontroller
VCC
VSS
6
1
is a 15 nF fixed
to C
4689F–RKE–08/06
4
are 68 nF
2