XT09-SI-MESH Digi International, XT09-SI-MESH Datasheet - Page 67

• Manufacturer Part Number: XT09-SI-MESH
• Description: MODULE RF 900MHZ 1W 115K W/RPSMA
• Manufacturer: Digi International

Specifications of XT09-SI-MESH

• Frequency: 900MHz
• Modulation Or Protocol: FHSS, FSK
• Power - Output: 1W
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 5.5 V
• Current - Receiving: 80mA
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -
• Data Interface: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 602-1183

Yagi antennas (approved when operating at 100 mW power output or lower)
XTend™ RF Module ‐ Product Manual v2.x6x
Part Number
A09-Y10TM
A09-Y12TM
A09-Y13TM
A09-Y14TM
A09-Y14TM
A09-Y15TM
A09-Y15TM
A09-Y11TM
A09-Y6TM
A09-Y7TM
A09-Y8TM
A09-Y9TM
A09-Y10
A09-Y11
A09-Y12
A09-Y13
A09-Y14
A09-Y14
A09-Y15
A09-Y15
A09-Y6
A09-Y7
A09-Y8
A09-Y9
IC (Industry Canada) Certification
C-TICK (Australia) Certification
Labeling Requirements
Power Requirements
Labeling requirements for Industry Canada are similar to those of the FCC. A clearly visible label
on the outside of the final product must display the following text:
The integrator is responsible for its product to comply with IC ICES-003 and FCC Part 15, Sub. B -
Unintentional Radiators. ICES-003 is the same as FCC Part 15 Sub. B and Industry Canada
accepts FCC test report or CISPR 22 test report for compliance with ICES-003.
Regulations in Australia stipulate a maximum of 30 dBm EIRP (Effective Isotropic Radiated Power).
The EIRP equals the sum (in dBm) of power output, antenna gain and cable loss and cannot not
exceed 30 dBm.
Figure A‐02. EIRP Formula for Australia
NOTE: The maximum EIRP for the FCC (United States) and IC (Canada) is 36 dBm.
These modules comply with requirements to be used in end products in Australia. All products
with EMC and radio communications must have a registered C-Tick mark. Registration to use the
compliance mark will only be accepted from Australian manufacturers or importers, or their agent,
in Australia. In order to have a C-Tick mark on an end product, a company must comply with a or
b below:
© 2010 Digi Internatonal, Inc.
Contains Model XTend Radio, IC: 4214A-9XTEND
10 Element Yagi
12 Element Yagi
13 Element Yagi
15 Element Yagi
10 Element Yagi
12 Element Yagi
13 Element Yagi
15 Element Yagi
2 Element Yagi
3 Element Yagi
4 Element Yagi
4 Element Yagi
5 Element Yagi
6 Element Yagi
7 Element Yagi
9 Element Yagi
2 Element Yagi
3 Element Yagi
4 Element Yagi
4 Element Yagi
5 Element Yagi
6 Element Yagi
7 Element Yagi
9 Element Yagi
Type
Connector
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPTNC
RPN
RPN
RPN
RPN
RPN
RPN
RPN
RPN
RPN
RPN
RPN
RPN
10.1 dBi
11.1 dBi
12.1 dBi
13.1 dBi
14.1 dBi
14.1 dBi
15.1 dBi
15.1 dBi
10.1 dBi
11.1 dBi
12.1 dBi
13.1 dBi
14.1 dBi
14.1 dBi
15.1 dBi
15.1 dBi
6.1 dBi
7.1 dBi
8.1 dBi
9.1 dBi
6.1 dBi
7.1 dBi
8.1 dBi
9.1 dBi
Gain
Application
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
Fixed / Mobile
67