XBP09-DPUIT-156 Digi International, XBP09-DPUIT-156 Datasheet - Page 38

• Manufacturer Part Number: XBP09-DPUIT-156
• Description: MODULE XBEE PRO W/U.FL
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP09-DPUIT-156

• Frequency: 902MHz ~ 928MHz
• Data Rate - Maximum: 156kbps
• Modulation Or Protocol: FHSS
• Applications: ISM
• Power - Output: 17dBm (50mW)
• Sensitivity: -100dBm
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Receiving: 80mA
• Current - Transmitting: 210mA
• Data Interface: PCB, Through Hole
• Antenna Connector: U.FL
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 602-1168

I/O Commands
XBee‐PRO® 900 RF Modules
AT
Command
D8
D9
PR
M0
M1
LT
IS
Name and Description
DIO8 Configuration.
Configure options for the DIO8 line of the module. Options include:
0 = Input, unmonitored
3 = Digital input, monitored
4 = Digital output low
5 = Digital output high
DIO9 / ON/SLEEP.
Configuration. Configure options for the DIO9/ON/SLEEP line of the module. Options
include:
0 = Input, unmonitored
1 = ON/SLEEP
3 = Digital input, monitored
4 = Digital output low
5 = Digital output high
Pull-up Resistor. Set/read the bit field that configures the internal pull-up resistor status
for the I/O lines. "1" specifies the pull-up resistor is enabled. "0" specifies no pullup.
Bit
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Note 1: When set as a digital input with pull-up disabled, the leakage can be 9 uA in the
worst case and 90nA in typical case when the line is set externally at a low level.
Note 2: When set as a digital input with pull-up enabled, the voltage of line will stabilize
between Vcc-0.65V and Vcc-0.45V
PWM0 Output Level.
Set/read the output level of the PWM0 line. The line should be configured as a PWM
output using the P0 command.
PWM1 Output Level.
Set/read the output level of the PWM1 line. The line should be configured as a PWM
output using the P1 command.
Assoc LED Blink Time.
Set/Read the Associate LED blink time. If the Associate LED functionality is enabled (D5
command), this value determines the on and off blink times for the LED. If LT=0, the
default blink rate will be used (500ms sleep coordinator, 250ms otherwise). For all other
LT values, LT is measured in 10ms
Force Sample.
Forces a read of all enabled digital and analog input lines.
IO Line
DIO4/AD4
AD3 / DIO3
AD2 / DIO2
AD1 / DIO1
AD0 / DIO0
RTS / DIO6
DTR / SLEEP_RQ/DI08
DIN / Config
Associate / DIO5
On/Sleep / DIO9
DIO12
PWM0 / RSSI / DIO10
DIO7/CTS
DOUT
PWM1 / DIO11
© 2009 Digi International, Inc.
Module pin
11
17
18
19
20
16
9
3
15
13
4
6
7
12
2
Range
55K - 330K
5K - 23K
5K - 23K
5K - 23K
5K - 23K
5K - 23K
5K - 23K
5K - 23K
55K - 330K
5K - 23K
5K - 23K
5K - 23K
5K - 23K
5K - 23K
5K - 23K
Notes
1
2
2
2
2
2
2
2
1
2
2
2
2
2
2
Parameter Range
0,3-5
0,1,3-5
0 - 7FFF
0-0x03FF
0-0x03FF
0x14-0xFF (x10ms)
n/a
Default
0
0x3F7F
0
0
0
n/a
38