S9S08DN32F1MLC Freescale Semiconductor, S9S08DN32F1MLC Datasheet - Page 35

• Manufacturer Part Number: S9S08DN32F1MLC
• Description: IC MCU 8BIT 32KB FLASH 32LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of S9S08DN32F1MLC

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LQFP
• Processor Series: S08D
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 26
• Operating Supply Voltage: 3 V to 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

To maintain I/O states for pins that were configured as general-purpose I/O before entering stop2, the user
must restore the contents of the I/O port registers, which have been saved in RAM, to the port registers
before writing to the PPDACK bit. If the port registers are not restored from RAM before writing to
PPDACK, then the pins will switch to their reset states when PPDACK is written.
For pins that were configured as peripheral I/O, the user must reconfigure the peripheral module that
interfaces to the pin before writing to the PPDACK bit. If the peripheral module is not enabled before
writing to PPDACK, the pins will be controlled by their associated port control registers when the I/O
latches are opened.
3.6.3
When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even
in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate,
clocks to the peripheral systems are halted to reduce power consumption. Refer to
Mode” and
Freescale Semiconductor
On-Chip Peripheral Modules in Stop Modes
Section 3.6.1, “Stop3 Mode
1
2
3
4
CPU
RAM
Flash/EEPROM
Parallel Port Registers
ACMP
ADC
IIC
MCG
RTC
SCI
SPI
TPM
Voltage Regulator
XOSC
I/O Pins
BDM
LVD/LVW
Requires the asynchronous ADC clock and LVD to be enabled, else in standby.
IRCLKEN and IREFSTEN set in MCGC1, else in standby.
Requires the RTC to be enabled, else in standby.
Requires the LVD or BDC to be enabled.
Peripheral
MC9S08DN60 Series Data Sheet, Rev 3
Table 3-2. Stop Mode Behavior
” for specific information on system behavior in stop modes.
Optionally On
States Held
Standby
Stop2
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
6
7
3
Mode
Optionally On
Optionally On
Optionally On
Optionally On
Optionally On
Optionally On
Optionally On
States Held
Standby
Standby
Standby
Standby
Standby
Standby
Standby
Standby
Stop3
Off
Chapter 3 Modes of Operation
Section 3.6.2, “Stop2
1
2
3
4
5
35