MPC8536BVTAUL Freescale Semiconductor, MPC8536BVTAUL Datasheet - Page 116

• Manufacturer Part Number: MPC8536BVTAUL
• Description: Microprocessors (MPU) 8536 INDUSTRIAL 1333
• Manufacturer: Freescale Semiconductor

Specifications of MPC8536BVTAUL

• Processor Series: MPC85xx
• Core: e500
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 1333 MHz
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Interface Type: I2C, SPI, UART
• Minimum Operating Temperature: 0 C
• Package / Case: FCPBGA-783
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Configuration Pin Muxing
To measure Z
value of each resistor is varied until the pad voltage is OV
components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and
R
are designed to be close to each other in value. Then, Z
Table 81
105°C.
Impedance
Note: Nominal supply voltages. See
3.9
The MPC8535E provides the user with power-on configuration options which can be set through the use of external pull-up or
pull-down resistors of 4.7 kΩ on certain output pins (see customer visible configuration pins). These pins are generally used as
output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins while HRESET is
asserted, is latched when HRESET deasserts, at which time the input receiver is disabled and the I/O circuit takes on its normal
function. Most of these sampled configuration pins are equipped with an on-chip gated resistor of approximately 20 kΩ. This
value should permit the 4.7-kΩ resistor to pull the configuration pin to a valid logic low level. The pull-up resistor is enabled
only during HRESET (and for platform /system clocks after HRESET deassertion to ensure capture of the reset value). When
the input receiver is disabled the pull-up is also, thus allowing functional operation of the pin as an output with minimal signal
quality or delay disruption. The default value for all configuration bits treated this way has been encoded such that a high voltage
116
P
is trimmed until the voltage at the pad equals OV
R
R
N
P
summarizes the signal impedance targets. The driver impedances are targeted at minimum V
Configuration Pin Muxing
0
Control, Configuration, Power
Local Bus, Ethernet, DUART,
for the single-ended drivers, an external resistor is connected from the chip pad to OV
MPC8535E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 3
Management
45 Target
45 Target
Table
Figure 77. Driver Impedance Measurement
Data
Table 81. Impedance Characteristics
1.
45 Target (cfg_pci_impd=1)
25 Target (cfg_pci_impd=0)
45 Target (cfg_pci_impd=1)
25 Target (cfg_pci_impd=0)
DD
0
/2. R
= (R
DD
P
/2 (see
P
PCI
then becomes the resistance of the pull-up devices. R
+ R
N
)/2.
Figure
Pad
R
R
OV
OGND
N
P
77). The output impedance is the average of two
DD
18 Target (full strength mode)
36 Target (full strength mode)
18 Target (full strength mode)
36 Target (full strength mode)
SW2
SW1
DDR DRAM
Freescale Semiconductor
DD
DD
, nominal OV
or GND. Then, the
Symbol Unit
Z
Z
P
0
0
and R
DD
,
Ω
Ω
N