LIS302DL STMicroelectronics, LIS302DL Datasheet - Page 21
![Board Mount Accelerometers MEMS motion snsr 3 axis](/photos/16/15/161592/lga-16_sml.jpg)
LIS302DL
Manufacturer Part Number
LIS302DL
Description
Board Mount Accelerometers MEMS motion snsr 3 axis
Manufacturer
STMicroelectronics
Datasheet
1.LIS302DL.pdf
(42 pages)
Specifications of LIS302DL
Sensing Axis
X, Y, Z
Acceleration
2 g, 8 g
Digital Output - Number Of Bits
8 bit
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.5 V
Supply Current
0.3 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Digital Output - Bus Interface
I2C, SPI
Shutdown
Yes
Sensitivity
18 mg/digit, 72 mg/digit
Package / Case
LGA-14
Output Type
Digital
Acceleration Range
±2g, ±8g
No. Of Axes
3
Interface Type
I2C, SPI
Sensor Case Style
LGA
No. Of Pins
14
Supply Voltage Range
2.16V To 3.6V
Operating Temperature Range
-40°C To +85°C
Svhc
No
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LIS302DL
Manufacturer:
STM
Quantity:
10 500
Part Number:
LIS302DL
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
LIS302DLHS0.5
Manufacturer:
INNOLUX
Quantity:
1 000
Company:
Part Number:
LIS302DLHTR
Manufacturer:
SANYO
Quantity:
11
Company:
Part Number:
LIS302DLTR
Manufacturer:
ST
Quantity:
1 056
Part Number:
LIS302DLTR
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
LIS302DLTR8
Manufacturer:
SONY
Quantity:
26
Part Number:
LIS302DLTR8
Manufacturer:
ST
Quantity:
20 000
LIS302DL
Digital interfaces
Figure 6.
Read & write protocol
CS
SPC
SDI
DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0
RW
MS
AD5 AD4 AD3 AD2 AD1 AD0
SDO
DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0
CS is the Serial Port Enable and it is controlled by the SPI master. It goes low at the start of
the transmission and goes back high at the end. SPC is the Serial Port Clock and it is
controlled by the SPI master. It is stopped high when CS is high (no transmission). SDI and
SDO are respectively the Serial Port Data Input and Output. Those lines are driven at the
falling edge of SPC and should be captured at the rising edge of SPC.
Both the Read Register and Write Register commands are completed in 16 clock pulses or
in multiple of 8 in case of multiple byte read/write. Bit duration is the time between two falling
edges of SPC. The first bit (bit 0) starts at the first falling edge of SPC after the falling edge
of CS while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the
rising edge of CS.
bit 0: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0)
from the device is read. In latter case, the chip will drive SDO at the start of bit 8.
bit 1: MS bit. When 0, the address will remain unchanged in multiple read/write commands.
When 1, the address will be auto incremented in multiple read/write commands.
bit 2-7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DI(7:0) (write mode). This is the data that will be written into the device (MSb
first).
bit 8-15: data DO(7:0) (read mode). This is the data that will be read from the device (MSb
first).
In multiple read/write commands further blocks of 8 clock periods will be added. When MS
bit is 0 the address used to read/write data remains the same for every block. When MS bit
is 1 the address used to read/write data is incremented at every block.
The function and the behavior of SDI and SDO remain unchanged.
21/42