PV32H202A01B00 Murata Electronics North America, PV32H202A01B00 Datasheet - Page 10



Manufacturer Part Number
Murata Electronics North America

Specifications of PV32H202A01B00

Resistance (ohms)
Termination Style
PC Pin
Power (watts)
0.5W, 1/2W
Temperature Coefficient
Number Of Turns
Adjustment Type
Top Adjustment
Resistive Material
Mounting Type
Through Hole
Package / Case
Round - 0.260" Dia x 0.181" H (6.60mm x 4.60mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Part Number
Part Number:
240 000
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. If the trimmer potentiometer is used in DC and high
1. Soldering
PVZ2/PVA2 Series Notice
(1) Reflow soldering method and soldering iron are
(2) Use our standard land dimension. Excessive land
(3) Soldering condition
(4) Apply the appropriate amount of solder paste.
Notice (Operating and Storage Conditions)
relative humidity of 30-85%.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
humidity conditions, please connect wiper (#2) for
plus and resistive element (#1 or #3) for minus.
(PVZ Series only)
Notice (Soldering and Mounting)
available. Cannot be soldered using the flow
soldering method (dipping). If you use the flow
soldering method, the trimmer potentiometer may
not function.
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the
dimension of land pattern used should be Murata's
standard land pattern at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(5) The soldering iron should not come in contact
(1) Do not apply excessive force, preferably 4.9N
(2) Do not warp and/or bend PC board to prevent
(3) In chip placers, the recommended size of the
(1) In case there is flux on the resistive element,
(2) Isopropyl-alcohol and Ethyl-alcohol are
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
max. (Ref. 500gf) when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 1.5-1.8mm dia. and inner dimension
1.3mm dia.
clean sufficiently with cleaning solvents and
completely remove all residual flux.
applicable solvents for cleaning. If you use any
other types of solvents, please evaluate
performance with your product.