LIS331DLHTR STMicroelectronics, LIS331DLHTR Datasheet - Page 28

• Manufacturer Part Number: LIS331DLHTR
• Description: ACCELEROMETER MEMS 3AXIS 16-LGA
• Manufacturer: STMicroelectronics
• Series: MEMS, nanor

Specifications of LIS331DLHTR

• Featured Product: STM32 Cortex-M3 Companion Products
• Axis: X, Y, Z
• Acceleration Range: ± 2g, 4g, 8g
• Sensitivity: 3.9mg/digit, 2mg/digit, 1mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 100Hz ~ 400Hz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 16-LGA
• Package Type: LGA
• Operating Supply Voltage (min): 2.16V
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 3mm
• Product Height (mm): 1mm
• Product Length (mm): 3mm
• Mounting: Surface Mount
• Pin Count: 16
• Sensing Axis: X, Y, Z
• Acceleration: 2 g, 4 g, 8 g
• Digital Output - Number Of Bits: 16 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Supply Current: 250 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Mounting Style: SMD/SMT
• Shutdown: Yes
• For Use With: 497-10672 - PLATFORM MUSA497-10048 - BOARD EVAL ACCELEROMETER497-9053 - DEMO BOARD FOR LIS331DLH497-8852 - BOARD DEMO STM8S207R6/LIS331DLH497-8851 - BOARD DEMO STM8S207R6/LIS331DLH
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10397-2; LIS331DLHTR

Register description
7.4
7.5
28/38
CTRL_REG3 [Interrupt CTRL register] (22h)
Table 25.
Table 26.
Table 27.
CTRL_REG4 (23h)
Table 28.
Table 29.
IHL
PP_OD
LIR2
I2_CFG1,
I2_CFG0
LIR1
I1_CFG1,
I1_CFG0
BDU
BLE
BDU
IHL
I1(2)_CFG1
0
0
1
1
CTRL_REG3 register
CTRL_REG3 description
Data signal on INT 1 and INT 2 pad
CTRL_REG4 register
CTRL_REG4 description
PP_OD
Block data update. Default value: 0
(0: continuos update; 1: output registers not updated between MSB and LSB reading)
Big/little endian data selection. Default value 0.
(0: data LSB @ lower address; 1: data MSB @ lower address)
BLE
Interrupt active high, low. Default value: 0
(0: active high; 1:active low)
Push-pull/Open drain selection on interrupt pad. Default value 0.
(0: push-pull; 1: open drain)
Latch interrupt request on INT2_SRC register, with INT2_SRC register cleared by
reading INT2_SRC itself. Default value: 0.
(0: interrupt request not latched; 1: interrupt request latched)
Data signal on INT 2 pad control bits. Default value: 00.
(see table below)
Latch interrupt request on INT1_SRC register, with INT1_SRC register cleared by
reading INT1_SRC register. Default value: 0.
(0: interrupt request not latched; 1: interrupt request latched)
Data signal on INT 1 pad control bits. Default value: 00.
(see table below)
LIR2
FS1
I1(2)_CFG0
Doc ID 15094 Rev 3
0
1
0
1
I2_CFG1
FS0
I2_CFG0
STsign
Interrupt 1 source OR interrupt 2 source
Interrupt 1 (2) source
LIR1
0
INT 1(2) Pad
Boot running
Data ready
I1_CFG1
ST
LIS331DLH
I1_CFG0
SIM