AT80C51RD2-SLSUM Atmel, AT80C51RD2-SLSUM Datasheet - Page 30

• Manufacturer Part Number: AT80C51RD2-SLSUM
• Description: MCU, 8BIT, 8051, 5V, SPI, 20MHZ, 44PLCC
• Manufacturer: Atmel

Specifications of AT80C51RD2-SLSUM

• Controller Family/series: (8051) 8052
• No. Of I/o's: 32
• Ram Memory Size: 1280Byte
• Cpu Speed: 40MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 5
• Core Size: 8bit
• Oscillator Type: External Only
• Processor Series: AT80x
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Type: ROMLess
• Data Ram Size: 1280 B
• Interface Type: UART, SPI
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: PLCC
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Cpu Family: AT80
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 1.25KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.1
Figure 10-3. PCA Capture Mode
10.2
30
PCA Capture Mode
16-bit Software Timer/ Compare Mode
AT80C51RD2
Cex.n
To use one of the PCA modules in the capture mode either one or both of the CCAPM bits
CAPN and CAPP for that module must be set. The external CEX input for the module (on port 1)
is sampled for a transition. When a valid transition occurs the PCA hardware loads the value of
the PCA counter registers (CH and CL) into the module's capture registers (CCAPnL and CCA-
PnH). If the CCFn bit for the module in the CCON SFR and the ECCFn bit in the CCAPMn SFR
are set then an interrupt will be generated (see Figure 10-3).
The PCA modules can be used as software timers by setting both the ECOM and MAT bits in
the modules CCAPMn register. The PCA timer will be compared to the module's capture regis-
ters and when a match occurs an interrupt will occur if the CCFn (CCON SFR) and the ECCFn
(CCAPMn SFR) bits for the module are both set (see Figure 10-4).
CF
ECOMn
CR
CAPPn
CAPNn MATn TOGn PWMn ECCFn
CCF4 CCF3 CCF2 CCF1 CCF0
Capture
CCAPMn, n= 0 to 4
0xDA to 0xDE
CCON
0xD8
CCAPnH
PCA Counter/Timer
CH
CCAPnL
CL
PCA IT
4113D–8051–01/09