PIC16F88-E/ML Microchip Technology, PIC16F88-E/ML Datasheet - Page 38

• Manufacturer Part Number: PIC16F88-E/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F88-E/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: SSP, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28QFN3 - SOCKET TRAN ICE 18DIP/28QFNAC164033 - ADAPTER 28QFN TO 18DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Details

PIC16F87/88
FIGURE 4-2:
TABLE 4-2:
DS30487C-page 36
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values were not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following this table for additional
information.
DD
Note:
Note 1: See Table 4-2 for typical values of C1 and
Mode
HS
XT
and temperature range for the application.
2: A series resistor (R
3: R
C1
C2
Typical Capacitor Values Used:
(1)
(1)
When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any V
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of R
C2.
(typically between 2 M to 10 M
F
16.0 MHz
2.0 MHz
4.0 MHz
8.0 MHz
455 kHz
Freq
RES
R
varies with the resonator chosen
S (2)
CERAMIC RESONATORS
(FOR DESIGN GUIDANCE
ONLY)
OSC1
OSC2
CERAMIC RESONATOR
OPERATION (HS OR XT
OSC CONFIGURATION)
S
R
) may be required.
OSC1
56 pF
47 pF
33 pF
27 pF
22 pF
F (3)
S
PIC16F87/88
is 330
To Internal
Logic
Sleep
.
OSC2
56 pF
47 pF
33 pF
27 pF
22 pF
DD
for
4.3
The ECIO Oscillator mode requires an external clock
source to be connected to the OSC1 pin. There is no
oscillator start-up time required after a Power-on
Reset, or after an exit from Sleep mode.
In the ECIO Oscillator mode, the OSC2 pin becomes
an additional general purpose I/O pin. The I/O pin
becomes bit 6 of PORTA (RA6). Figure 4-3 shows the
pin connections for the ECIO Oscillator mode.
FIGURE 4-3:
Clock from
Ext. System
External Clock Input
RA6
EXTERNAL CLOCK INPUT
OPERATION
(ECIO CONFIGURATION)
 2005 Microchip Technology Inc.
OSC1/CLKI
I/O (OSC2)
PIC16F87/88