3UG4622-1AW30 SIEMENS, 3UG4622-1AW30 Datasheet - Page 29

• Manufacturer Part Number: 3UG4622-1AW30
• Description: RELAY, MONITOR, 22.5MM
• Manufacturer: SIEMENS
• Series: 3UG46r

Specifications of 3UG4622-1AW30

• Contact Configuration: SPCO
• Power Consumption: 4VA
• Supply Voltage Max: 240VAC
• Contact Current Max: 3A
• Relay Mounting: DIN Rail
• Coil Voltage Vac Nom: 230V
• External Depth: 86mm
• Coil Frequency Max: 60Hz
• Coil Operating Frequency Min: 50Hz

■
Technical specifications
Permissible ambient temperature
Permissible storage temperature
Installation altitude above sea level
Degree of protection (acc. to IEC 60529)
Shock resistance (sine pulse)
Mounting position
Mounting
• Max. set current I
• Max. set current I
EMC interference immunity
• Conducted interference, burst acc. to IEC 61000-4-4
• Conducted interference, surge acc. to IEC 61000-4-5
• Electrostatic discharge acc. to IEC 61000-4-2
• Field-related interference acc. to IEC 61000-4-3
EMC interference emission
Safe isolation
(product version 12 upwards, start of delivery 01/2000)
Displays
• Green "Ready" LED
• Green "BUS" LED
• Red "General Fault" LED
Test/Reset buttons
System interfaces
PROFIBUS DP interface
Main circuits
Rated insulation voltage U
(with pollution degree 3)
• For uninsulated conductors (3UF5 001 to 3UF5 021)
• For insulated conductors (3UF5 001 to 3UF5 021)
• For uninsulated and insulated conductors
Rated impulse withstand voltage U
• 3UF5 001 to 3UF5 021
• 3UF5 031 to 3UF5 051
Rated frequency
Type of current
Short-circuit protection
Diameters of feed-through openings
(max. I
• Devices with max. set current I
• Devices with max. set current I
• Devices with max. set current I
Busbar connections
• Current range
• Tightening torque
• Finely stranded with cable lug
• Stranded with cable lug
Shared data of basic units/expansion units/
expansion modules/operator panels
Basic units
(3UF5 031 to 3UF5 051)
e
= 100 A)
e
e
ˆ 100 A
> 100 A
SIMOCODE 3UF Motor Management and Control Devices
i
e
e
e
ˆ 25 A
ˆ 100 A
> 100 A
imp
°C
°C
m
g/ms
kV
kV
kV
V/m
V
V
V
kV
kV
Hz
mm
mm
A
Nm
mm
mm
2
2
-25 ... +60
-40 ... +80
ˆ 2000
IP20 max. set current I
IP00 max. set current I
10/5
Any
Snap-on mounting onto 35 mm standard mounting rail or
screw fixing with push-in lugs
Screw fixing directly onto contactor or screw fixing
2 (corresponds to degree of severity 3)
2 (corresponds to degree of severity 3)
8 (corresponds to degree of severity 3)
10 (corresponds to degree of severity 3)
Limit class B acc. to EN 55011 (VDE 0875 Part 11)
All electric circuits in SIMOCODE-DP are safely isolated from each other,
i.e. they are designed with double leakage paths and clearances
Power circuit from the control/electronic circuits:
Safe isolation up to 690 V or 1000 V between control and electronic circuits
One below the other: Safe isolation up to 300 V
Observe notes of test report "Safe Isolation" No. 1610a.
Continuous light: "Ready"
Off: "No control supply voltage" or "Function test not OK; device is disabled"
Continuous light: "Bus operation"
Continuous light/blinklight: "Feeder fault", e.g. overload tripping
By pressing the Test/Reset button, the device can be reset following a trip or its
functions can be tested
RS 232 for connecting the expansion module, operator panel or PC
RS 485 for connecting the PROFIBUS DP line using terminals (conductor cross-
sections as for auxiliary contacts) or 9-pole SUB D socket
690
1000
1000
6
8
50/60
Three-phase current
See table Short-circuit protection with fuses for motor feeders, page 7/31
10
15
Design with connecting bars
50 ... 205
M 8: 10 ... 14
35 ... 95
50 ... 120
e
e
ˆ 100 A;
> 100 A
125 ... 500
M 10: 14 ... 24
50 ... 240
70 ... 240
motor protection and control devices
Siemens LV 1 T · 2006
SIMOCODE-DP 3UF5
200 ... 820
M 10: 14 ... 24
M 12: 20 ... 35
50 ... 240
70 ... 240
7/29