T1620000 Red Lion Controls, T1620000 Datasheet - Page 15

• Manufacturer Part Number: T1620000
• Description: Process/Temperature Controller
• Manufacturer: Red Lion Controls
• Type: Temperaturer

Specifications of T1620000

• Operating Temperature Max: 50°C
• Operating Temperature Min: 0°C
• Temperature Accuracy ±: 0.3%
• Output Voltage Max: 7V
• Output Voltage Min: 4V
• Controller Input: Thermocouple Or RTD
• Brand/series: T16 Series
• Dimensions: 49.5mmW×49.5mmH×115.3mmD
• Enclosure Rating: IP65
• Input Type: RTD/Thermocouple
• Ip Rating: IP65
• Memory: EEPROM
• Mounting Type: Panel
• Output Type: Digital/SSR
• Power, Rating: 8 VA
• Primary Type: Controller
• Special Features: EEPROM
• Standards: cURus, CE
• Termination: Screw
• Voltage, Supply: 85 to 250 VAC
• Thermocouple Type: J, K, T, E, R, S, B, N, C And Linear MV
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

set to current. They must be changed if voltage output is desired. The Analog
output can be calibrated to provide up to approximately 5% over range
operation (0 mA current can only go slightly negative).
track.
actuator or pen recorder activity.
The following parameters can be configured for
7.3 MODULE 3 - L
dISP
HIdE
LOC
dSPr
SETPOINT
ACCESS
4-20
dISP
ANtP
Select the type of output and range. The Analog output jumpers are factory
ANAS
This setting selects the parameter that the Analog Output will retransmit or
ANUt
The update time of the Analog Output can be used to reduce excess valve
SELECTION
OP
SP
(SP only)
0
ANALOG OUTPUT ASSIGNMENT (OPTIONAL)
ANALOG OUTPUT RANGE (OPTIONAL)
0-10
4-20
0
0
InP
ANALOG UPDATE TIME (OPTIONAL)
OP
SP
= update rate of 0.1 second
to
Display: accessible in Display Loop.
Hide: accessible in Hidden Loop.
Locked: not accessible in either loop.
Display/read: read only in Display Loop,
but read/write in Hidden Loop.
ACCESS
OUTPUT
POWER
dISP
mA
Main Control % Output Power
Input Signal Retransmission
Active Setpoint
V
250
OP
0-20
seconds
DESCRIPTION
mA
PID VALUES
ACCESS
HIdE
PId
OCKOUT
LOC
,
HIdE
PARAMETER MENU
, and
ACCESS
VALUES
ALARM
HIdE
P
ARAMETERS
AL
dISP
.
15
output as selected.
output as selected. An inverse acting output can be achieved by reversing the
low and high scaling points.
The following parameters can be configured for
The Analog Output assignment value that corresponds to 0 V, 0 mA or 4 mA
ANHI
100. 0
The Analog Output assignment value that corresponds to 10 V or 20 mA
CodE
0. 0
0
SETPOINT
ACCESS
SELECT
SPSL
(
LOC
-1
ANALOG HIGH SCALING (OPTIONAL)
1
ANALOG LOW SCALING (OPTIONAL)
-125
to
to
0
-999
AUTO-TUNE
-125
125
ACCESS
START
HIdE
tUNE
to
to
)
Full access to Display, Hidden,
and Configuration Loops
Code necessary to access
Configuration Loop only.
Code necessary to access
Hidden and Configuration Loops.
to
ACCESS CODE
9999
SETPOINT
ACCESS
SPrP
HIdE
RAMP
ALARMS
ACCESS
RESET
ALrS
LOC
TRANSFER
CONTROL
ACCESS
LOC
trnF
LOC
or
HIdE
only
.