IQ65033QMA10END-G SYNQOR, IQ65033QMA10END-G Datasheet - Page 4

• Manufacturer Part Number: IQ65033QMA10END-G
• Description: InQor DC/DC Converters
• Manufacturer: SYNQOR

Specifications of IQ65033QMA10END-G

• Dc / Dc Converter O/p Type: Fixed
• No. Of Outputs: 2
• Input Voltage: 36V To 75V
• Output Voltage: 5V
• Output Current: 10A
• Output Voltage 2: 3.3V
• Approval Bodies: UL, CUL, TUV, IEC
• Supply Voltage: 48V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Product # IQ65033QMA10
IQ65033QMA10 ELECTRICAL CHARACTERISTICS (Continued)
Specifications subject to change without notice. Specifications in bold are guaranteed by design over the temperature range -40º to 125ºC.
Parameter
Note 1: If the 5.0 V load current exceeds 100 mA, up to 200 mV of additional voltage drop is possible on the 5.0 V output.
Note 2: Maximum DC load at startup is 50 mA. Full load can be applied 700 ms after enable or 400 ms after the management power is up and running.
Note 3: Hold-up operation with Vin < 43 V not required by ATCA specification.
Note 4: 48 V output does not recover after hold-up event unless input is above Arm Hold-up threshold.
Note 5: Does not inhibit 48 V output and is non-latching.
ENABLE_A/B Threshold
Current Drain per Enable Pin (Vin = -75V)
DUAL ENABLE INPUT CHARACTERISTICS
-48V OUTPUT
Efficiency
Equivalent Resistance From Input Feed
Recommended External Output Filter Capacitance
Hot-Swap Startup Ramp dV/dt
Output Voltage Delay
Input Current Limit (Turns Off Hot-Swap Momentarily)
Input dV/dt Limit (Turns Off Hot-Swap Momentarily)
Short Circuit Duration to Initiate Hiccup Mode
Restart Time in Hiccup Mode
INPUT ORING
ORing MOSFET Turn On Current
ORing MOSFET Turn Off Current
ORing MOSFET Current Hysteresis
Turn On Time
Turn Off Time
HOLD-UP CAPACITOR INTERFACE
Hold-up Capacitor Trim Range
Hold-up Capacitor Charge Accuracy
External Hold-up Voltage Trim Resistor Power Dissipation
Hold-up Capacitor Charge Current
Switching Frequency
-48V_OUT Threshold
dV/dt on Hold-up Connect
Duration of Hold-up Connect
Delay Before Hold-up Connect is (Re)Armed
Hold-up Capacitor Discharge Resistance
Maximum Hold-up Capacitance
ISOLATED ALARM OUTPUT (ALARM = HIZ)
Input A/B Feed Voltage Alarm Threshold
Open Circuit Voltage
On-State Voltage
On-State Transistor Collector Current
Off-State Transistor Collector Current
Technical Specification
ATCA
NEDS (ON\OFF)
ETSI
300W Output Power
200W Output Power
To Arm Hold-up (ATCA/NEDS options)
To Initiate Hold-up (ATCA/NEDS)
To Arm Hold-up Connect (ETSI)
To Initiate Hold-up Connect (ETSI)
\
Phone [phone]
5
40.0\36.0 42.5\39.0 45.0\42.0
Min.
-36.9
-36.4
-32.4
-32.4
26.0
32.0
97.7
98.0
150
87.2
1.55
36.4
1.8
0.4
0.1
0.3
405
80
15
50
www.synqor.com
Typ.
98.2
98.5
17.5
0.25
-38.9
-38.5
-34.5
-34.5
28.5
34.0
90.0
1.65
38.4
120
100
200
250
600
450
2.0
1.0
0.4
0.6
0.1
0.2
40
90
40
80
40
50
2
2
1
Max.
31.0
36.0
0.36
-40.9
-40.4
-36.4
-36.4
250
200
270
650
92.8
1.75
3300
2.2
2.4
1.1
1.3
40.4
495
20
160
0.4
mA
95
µA
V
Doc.# 005-IQ5033S Rev. H
Units
V/ms
V/ms
V/s
mA
mW
KHz
ms
ms
mA
µF
µs
µs
µW
kΩ
V
V
V
V
A
A
A
A
µF
s
V
V
V
V
V
V
V
V
s
s
Notes & Conditions
At input feed voltage -48V_A/B; see Figure A
No load on 3.3V/5.0V outputs, Vin = -48V
See Note 2
No load; depends on external cap.; see Figure 5
Hold-up still active
2.49kΩ external trim resistance, 1% 100ppm/ºC
See Note 3
See Note 4
Can be set either above or below input voltage
Hold-up power converter
At VRTN_OUT w.r.t. -48V_OUT; see Figure A
48V output still enabled
Yields 55ms (200 W at 90 V cap charge)
At input feed voltage -48V_A/B; see Figure A
At 50mA
Package:
Outputs:
Current:
“
Input:
05/27/10
“
“
“
“
“
36-75 V
5.0 V/ 3.3 V
10 A
Quarter-brick
Page 4