HFBR-0410Z Avago Technologies US Inc., HFBR-0410Z Datasheet

HFBR-0410Z

Manufacturer Part Number

HFBR-0410Z

Description

DC-5MBd 820nm FiberOptic EvalKit

Manufacturer

Avago Technologies US Inc.

Datasheets

1.HFBR-4401Z.pdf (25 pages)

2.HFBR-0410Z.pdf (2 pages)

Specifications of HFBR-0410Z

Main Purpose

Interface, Fiber Optics

Embedded

Utilized Ic / Part

HFBR-1412Z, HFBR-2412Z

Primary Attributes

820nm, 5MBd

Operating Voltage

5 V

Description/function

Miniature Fiber Optic Evaluation Kit

Maximum Operating Temperature

+ 85 C

Minimum Operating Temperature

- 40 C

Operating Current

9 mA

Leaded Process Compatible

Yes

Rohs Compliant

Yes

Peak Reflow Compatible (260 C)

Yes

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Secondary Attributes

Lead Free Status / Rohs Status

Details

For Use With/related Products

HFBR-14x4Z, HFBR14x5Z, HFBR24x2Z

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Other names

516-2313

Current page: 1 of 2
Download datasheet (82Kb)

HFBR-0410Z Evaluation Kit

DC to 5MBd 820nm Miniature Link Fiber Optic Evaluation Kit

User Guide

Introduction

HFBR-0410Z evaluation kit is used to evaluate Avago fiber optic device HFBR-1412Z and HFBR-2412Z. The evaluation kit

is equipped with necessary documents and accessories to ease product evaluation and verification.

Evaluation Kit

HFBR-0410Z contains:

1. Evaluation board

2. HFBR-1412Z and HFBR-2412Z unit

3. HFBR-1412Z/2412Z datasheet

4. User guide document

Evaluation Board

The basic evaluation board that you receive from Avago incorporates transmitter driver IC SN75451BD, some passive

components, and SMA connectors for the TX input (TXD) and RX output (RXD) port connection. This basic evaluation

board allows you to connect waveform/pattern generator to the TXD with TTL input signal. Receiver’s output signal can

be monitored from the RXD or RXout with oscilloscope by using high impedance setting.

Initial Setup

1. Connect 5 V supply voltage to TXVCC and RXVCC

2. Connect 0 V to TXGND and RXGND

3. Connect TXD to pattern generator output

4. Connect RXout to Oscilloscope with high impedance probe

Bit Error Rate Test Setup

Though the transmitter driver IC’s input and receiver’s output is based on TTL logic (high impedance), the board can be

modified to connect 50ohm load instrument by doing the following steps:

1. Put R2 (50 ohm resistor).

2. Remove R3 (0 ohm resistor).

3. Put R4 (0 ohm resistor) and R7 (50 ohm resistor).

4. Put U3 (SN74LVC2G125).

5. Connect BVCC (5 V) and BGND (0 V).

Related parts for HFBR-0410Z

HFBR-0410Z Summary of contents

Page 1

... DC to 5MBd 820nm Miniature Link Fiber Optic Evaluation Kit User Guide Introduction HFBR-0410Z evaluation kit is used to evaluate Avago fiber optic device HFBR-1412Z and HFBR-2412Z. The evaluation kit is equipped with necessary documents and accessories to ease product evaluation and verification. Evaluation Kit HFBR-0410Z contains: 1 ...

Page 2

For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in ...

Related keywords

HFBR-0410Z datasheet
HFBR-0410Z data sheet
HFBR-0410Z pdf datasheet
HFBR-0410Z component
HFBR-0410Z part
HFBR-0410Z distributor
HFBR-0410Z RoHS
HFBR-0410Z datasheet download