HFBR-0562 Avago Technologies US Inc., HFBR-0562 Datasheet - Page 5
![Fiber Optics, Evaluation Kit](/photos/37/14/371435/5968-9719e_sml.jpg)
HFBR-0562
Manufacturer Part Number
HFBR-0562
Description
Fiber Optics, Evaluation Kit
Manufacturer
Avago Technologies US Inc.
Specifications of HFBR-0562
Silicon Manufacturer
Avago
Silicon Core Number
HFBR-591xE, HFCT-591xE
Kit Application Type
Communication & Networking
Application Sub Type
MT-RJ Gigabit Ethernet Transceiver
Main Purpose
Interface, Ethernet
Embedded
No
Utilized Ic / Part
HFCT-591xE, HFBR-591xE
Primary Attributes
MT-RJ 1.25Gb Multimode Applications
Secondary Attributes
MT-RJ Fiber Connector Interface
Description/function
Fiber Optic Kit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
HFBR-591x
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
5
Interfacing/Termination Schemes
Figure 5 shows the recommended
interface termination scheme for
1.25 Gb/s SFF transceivers to Avago
Gigabit Ethernet SerDes ICs, the
HDMP-1636A/1646A. It assumes that
the 3.3 V power supply is common
to both the fiber optic transmitter
and receiver so that the alternative
Notes:
Use surface-mount components for optimum high-frequency performance.
Use 50 microstrip or stripline for signal paths.
Locate 50 terminations at the inputs of receiving units.
* In order to eliminate required external passive components, agilent has included the equivalent of resistors
** C8 is a recommended bypass capacitor for additional low frequency noise filtering.
Figure 5. Recommended Gigabit/sec Ethernet HFBR/HFCT-591xE Fiber Optic transceiver and HDMP-1636A/1646A SERDES integrated circuit transceiver
interface and power supply filter circuits
C5 and C6 within the module. R5 - R8, C5 and C6 are included as part of the application circuit to accommodate
vendors' modules. the HFBR/HFCT-591XE will operate in both configurations.
The signal detect output on the HFBR-591XE contains an internal 1.8 k pull up resistor. The output stage on the HFCT-591XE is a PU
pull configuration and therefore does not require an external pull up resistor.
PRE-
AMPLIFIER
CIRCUIT
DRIVER
LASER
HFBR/HFCT-591xE
TRANSCEIVER
FIBER-OPTIC
V
CC
TRANSMIT
DISABLE
CIRCUIT
SIGNAL
DETECT
POST-
AMPLIFIER
INPUT
PECL
100
TD+
TD-
V
V
V
1.8
k
RD+
V
SD
RD-
EET
CCT
CCR
EER
power supply filter shown in Figure 5
can be implemented.
The transmitter input stage is 50 W
terminated so that the +3.3 kW/+5.1
kW resistors provide bias only. These
termination resistors should be po-
sitioned as close as possible to the
device pin.
7
9
10
8
6
2
3
4
5
1
LVTTL
STAGE
0.1 F
C1
0.1 F
C2
0.1 F
TO
C11
R3
130
5.1 k
C8**
10 F
R5*
R7*
3.3 k
R4
130
R6*
5.1 k
1 H
1 H
L1
L2
TO LVTTL STAGE
R8*
3.3 k
3.3 Vdc
C9
0.1 F
C5*
0.01 F
C6*
0.01 F
C7
0.1 F
C4
0.01 F
C3
0.01 F
50
50
3.3 Vdc
R10
150
+
50
R14
50
100
C10
10 F
R9
150
V
SEE HDMP-1636A/-1646A DATA SHEE
DETAILS ABOUT THIS TRANSCEIVER IC
TD+
TD-
RD-
RD+
CC
2
V
INPUT
BUFFER
OUTPUT
EE
DRIVER
SERIAL/DE-SERIALIZER
2
HDMP-1636A/-1646A
(SERDES - 10 BIT
TRANSCEIVER)
SYNTHESIS
PARALLEL
TO SERIAL
RECOVERY
SERIAL TO
PARALLEL
CIRCUIT
CIRCUIT
CIRCUIT
CIRCUIT
+
CLOCK
CLOCK
3.3 Vdc
GND